JVC UX-V55R manual Using the Cassette Deck Recording, Standard Recording

Page 19

Using the Cassette Deck

(Recording)

 

REMOTE CONTROL RM-RXUV5R

 

 

 

 

 

DIMMER

SLEEP

 

 

 

 

 

 

 

 

 

 

REV.DISPLAY

 

 

 

 

 

 

REC

MODE PTY/EON MODE

CLOCK

 

 

DISPLAY

FM MODE

MD/AUX

REC

 

TIMER/

REV. MODE

 

AHB PRO

VOLUME

SNOOZE

 

 

AHB PRO

AUTO

CD

 

 

 

 

 

PRESET

 

 

 

 

AUTO PRESET

PROGRAM RANDOM

REPEAT

 

 

 

 

 

 

 

 

 

 

BASS

TREBLE

CANCEL

 

 

 

 

 

 

UP

 

 

 

 

Tape Direction indicator

 

 

SET

 

 

 

 

 

 

 

DOWN

 

 

 

 

 

 

PTY/EON

 

DISPLAY MODE

 

 

 

 

TAPE @ #

TAPE

TUNER

CD

 

 

 

Reverse Mode

 

TAPE REC indicator

indicator

 

BAND

 

 

 

 

 

 

 

 

7

VOLUME

When the System is in use, the display shows other items as well.

For simplicity, we show here only the items described in this section.

English

Recording onto a tape from any of the sound sources is simple. Just place a tape in the Cassette Deck, have the source ready, make one or two settings, and you’re ready to record. For each source the pro- cedure is a little bit different so we explain each separately. But first, here are a few things to make your recordings better.

Things To Know Before You Start Recording —————————————

It may be unlawful to record or play back copyrighted material without the consent of the copyright owner.

When you want to record onto both sides of a tape, you can set Reverse mode to do so. Recording automatically stops after re- cording in the 2 direction. Therefore, make sure that the tape di- rection is 3 when recording with Reverse mode on.

The recording level, which is the volume at which the new tape is being made, is automatically set correctly, so it is not affected by the VOLUME control on the System. Nor is it affected by adjusting the sound effects. Thus, during recording you can ad- just the sound you are actually listening to without affecting the recording level.

Two small tabs on the back of the cassette tape, one for side A and one for side B, can be removed to prevent accidental erasure or recording.

Type II detection slot

Adhesive tape

To record on a cassette with the tabs removed, you must cover the holes with adhesive tape first. However, when a type II tape is used, only cover part of the hole as shown, since the other part of the hole (Type II detection slot) is used to detect the tape type.

Type I and Type II tapes can be used for recording.

Note: At the start and end of cassette tapes, there is leader tape which cannot be recorded onto. Thus, when recording CDs or radio broadcasts, wind on the leader tape first to ensure getting the begin- ning of the recording.

CAUTION: If a recording you make has excessive noise or static, the Unit may have been too close to a TV which was on during the recording. Either turn off the TV or increase the distance between the TV and the System.

Standard Recording

You can record any sound source to tape as follows:

1. Insert a blank or erasable tape into the

Cassette Deck and wind past the tape leader.

2. Press the REV. MODE button on the Unit if you want to record on both sides of the tape.

Press the button until the indicator is lit.

When using Reverse mode, insert the tape so that it will be recorded in the forward 3 direction.

3. Check the recording direction for the tape.

Make sure that the Tape Direction indicator is the same as that for the tape in the Cassette Deck. If the directions are different, press the TAPE @ # button to correct the tape direction and then press the e button to stop the tape.

4. Prepare the source, by, for example, tuning in a radio station or turning on connected auxiliary equipment.

Note: For CD recording, refer to “CD Direct Recording” men- tioned below.

5. Press the REC button on the Unit.

The “TAPE REC” indicator lights up and the System begins re- cording.

If the tab of the cassette tape is removed to prevent erasure or recording, “NO REC” will appear on the display.

15

Image 19
Contents UX-V55R Achtung Precaucion ventilación correcta Class Laser Product Table of Contents Getting Started AccessoriesHow To Put Batteries In the Remote Control Using the Remote ControlUsing the Coaxial Type Connector Not Supplied Connecting the FM AntennaConnecting the AM MW/LW Antenna Using the Supplied Wire AntennaConnecting External Equipment Connecting the SpeakersConnecting an MD Recorder, etc Digital Output On the Unit On the Remote Control Connecting the AC Power CordCommon Operations Turning the Power On and OffAdjusting the Volume Adjusting the Brightness DimmerBass Control Reinforcing the Bass Sound AHB PROTone Control BASS/TREBLE Showing the Time DisplayManual Presetting Using the TunerTuning In a Station Presetting StationsReceiving FM Stations with Auto PresettingTo Change the FM Reception Mode To show the RDS signals on the displayCodes To search for a programme by PTYPress the PTY/EON button within 10 sec- onds again News News To select a programme typeTo Unload a CD Using the CD PlayerBasics of Using CD Player-Normal Play To Insert a CDRandom Play Programming Playing Order of the TracksRepeating Tracks One Touch Play Using the Cassette Deck Listening to a TapeReverse Mode Regular PlayCheck the recording direction for the tape Using the Cassette Deck RecordingStandard Recording Things To Know Before You Start RecordingRecording an AM station to tape CD Direct RecordingOne Track Recording To Stop at Any Time During the Recording ProcessUsing External Equipment Setting the Clock Using the TimersSetting the Daily Timer Minute Snoozing Setting the Sleep TimerSetting the volume level Press the TIMER/SNOOZE button on UnitCare And Maintenance Action TroubleshootingSymptom Possible CauseSpecifications EN, GE, FR, NL, SP, IT, SW 0699MNMCREJSC