chronograph display format setting will blink.
3.Press S2 or S4 button to toggle be- tween LAP/SPL (lap time on top line and split time on bottom line) and SPL/LAP (split time on top line and lap time on bottom line) format.
4.When finished making the setting, press S1 button to confirm.
NOTE: Definitions of lap time and split time:
a)Lap time – individual lap time.
b)Split time – cumulative lap time.
NOTE: The selected chronograph display format will apply to both chro- nograph counting and chronograph recall function.
For the measurement of elapsed time: In CHRONOGRAPH mode,
1.Press S2 button to start counting.
2.To stop counting, press S4 button.
3.To restart counting and resume from where it left off, press S2 button again.
4.To reset to zero, press S4 button to stop counting and press and hold S4 button. The message “HOLD TO RESET” will be displayed for approximately 2 seconds and the counter will be reset to zero.
For the measurement of split time: In CHRONOGRAPH mode,
1.Press S2 button to start counting.
2.While the chronograph is running, press S2 button once to register a lap. The lap time and split time of the registered lap will be displayed and the lap number will be displayed intermittently. The chronograph is still running in the background. After approximately 10 seconds, the lap time and split time of the current lap will be displayed.
3.Repeat the last step until all the laps have been registered.
4.To stop counting, press S4 button.
5.To restart counting and resume from where it left off, press S2 button again.
6.To reset to zero, press S4 button to stop counting and press and hold S4 button. The message “HOLD TO RESET” will be displayed for approximately 2 seconds and the counter will be reset to zero.
NOTE: In a chronograph counting, the watch can register up to a maximum of 99 laps before start counting from lap 1 again. However, only the first 50 lap records will be stored and available for checking in recall function.
NOTE: You can leave the chronograph running while switching over to other operating modes.
NOTE: You can leave the chronograph running while switching over to other operating modes. The chronograph in-
dicator 
will be displayed in HOME TIME mode and FOREIGN TIME mode when the chronograph is in use.
TO USE THE RECALL FUNCTION:
In CHRONOGRAPH mode,
1.Press S1 button to select the recall function.
2.Press S2 or S4 button to cycle forward or backward through the stored lap records.
3.Press S1 button to return to CHRO- NOGRAPH mode.
NOTE: The recall function is available only when there is more than 1 lap record stored.
NOTE: The lap record will be cleared when the chronograph is reset.
TO SET THE TIMER:
1.Press S3 button to select TIMER mode.
2.Press S1 button, the message “SET” will be displayed and the hour digits will blink. Press S2 button to increase or S4 button to decrease the value. Holding down the button will speed up the process.
3.Press S3 button, the minute digits will blink. Press S2 button to in- crease or S4 button to decrease the value. Holding down the button will speed up the process.
4.Press S3 button, the second digits will blink. Press S2 button to in- crease or S4 button to decrease the value. Holding down the button will speed up the process.
5.Press S3 button, the
6.When finished making all the set- tings, press S1 button to confirm.
NOTE: Definitions of
a)STOP AT END – the timer will stop when the countdown reaches zero.
b)REPEAT AT END – the timer will repeat the countdown when the count- down reaches zero.
ENGLISH
TO USE THE TIMER:
1.Press S3 button to select TIMER mode.
2.The timer will then be displayed in its current state – stopped, running, or reset.
3.To resume a stopped counting, press S2 button to resume from where
it left off.
4.To start a new counting, reload the timer first.
Press S4 button to stop counting, then press S4 button again to reload the timer.
5.When reaching zero in a countdown, a tune will be emitted. To stop the tune, press any button.
TO USE THE BACKLIGHT:
Press S4 button to turn on the back- light for 3 seconds.
|
|
To reduce carbon foot print, these | FS1061&62 |
Freestyle instructions are printed with |
|
soy inks on recycled paper. |
|