JVC 0105RYMMDWJEIN manual Attenuating the Input Signal, Changing the Source Name, Basic Operations

Page 14
“DOLBY DIGITAL” or “DTS SURROUND.”

Basic Operations

English

When playing software encoded with Dolby Digital or DTS, the following symptoms may occur:

Sound does not come out at the beginning of playback.

Noise comes out while searching for or skipping chapters or tracks.

In this case, press INPUT DIGITAL repeatedly to select

Remote

“DOLBY DIGITAL” or “DTS SURROUND.”

NOT

Each time you press INPUT DIGITAL, the input mode changes as follows:

Attenuating the Input Signal

Remote

 

NOT

When the input level of the analog source is too high, the sounds will be distorted. If this happens, you need to attenuate the input signal level to prevent the sound distortion.

Once you have made adjustment, it is memorized for each analog source.

Attenuating the Input Signal DIGITAL AUTO  DIGITAL AUTO  DOLBY DIGITAL DOLBY DIGITAL

DTS SURROUND Changing the Source Name

When “DOLBY DIGITAL” or “DTS SURROUND” is selected,

the DIGITAL AUTO indicator goes off, and the corresponding digital signal format indicator lights up on the display.

If the incoming signal does not match the selected digital signal format, the indicator of the selected signal format will flash.

Note:

When you turn off the power or select another source, “DOLBY DIGITAL” and “DTS SURROUND” settings are canceled and the digital input mode is automatically reset to “DIGITAL AUTO.”

Press and hold INPUT ATT (INPUT ANALOG) so that the INPUT ATT indicator lights up on the display.

Each time you press and hold the button, the input attenuator mode turns on (“INPUT ATT ON”) and off (“INPUT NORMAL”).

Changing the Source Name

Remote

 

NOT

When you have connected a CD recorder to the TAPE/CDR jacks on the rear panel, change the source name which will be shown on the display.

To select the analog input mode

Press INPUT ANALOG (or ANALOG/DIGITAL on the remote control repeatedly until “ANALOG” appears on the display). The ANALOG indicator lights up.

Changing the Display Brightness

You can dim the display.

Press DIMMER.

Each time you press the button, the display dims and brightens alternately.

When changing the source name from “TAPE” to “CDR”:

1Press TAPE/CDR (SOURCE NAME).

• Make sure “TAPE” appears on the display.

2Press and hold SOURCE NAME (TAPE/CDR) until “ASSIGN CDR” appears on the display.

To change the source name back to “TAPE,” repeat the same

procedure above.

Note:

Without changing the source name, you can still use the connected components. However, there may be some inconvenience.

“TAPE” will appear on the display when you select the CD recorder.

You cannot use the digital input (see page 11) for the CD recorder.

12

Image 14
Contents AUDIO/VIDEO CONTROL RECEIVER EnglishRX-5052S INSTRUCTIONSCaution Proper Ventilation Warnings, Cautions, and OthersCaution--STANDBY/ON button RX-5052SUsing the Surround Modes Table of ContentsAdjusting Sound Using the DSP ModesParts Identification EnglishEnglish Checking the Supplied Accessories Before InstallationAdjusting the Voltage Selector Connecting the FM and AM Antennas2Press and hold the clamp of the speaker terminal Connecting the Speakers and SubwooferConnecting the speakers 3Insert the speaker cordGetting Started Connecting Audio/Video ComponentsConnecting the subwoofer Placing speakersDVD player Video component connectionsEnglish Getting Started Connecting the Power CordDigital Connections English3Adjust the volume Daily Operational Procedure1Turn on the power Turning On the PowerOn the remote control Adjusting the VolumeSpeaker and signal indicators on the display Basic OperationsSubwoofer Sound Listening with headphonesTurning On and Off the Selecting the Analog or Digital Input ModeChanging the Display Brightness Attenuating the Input SignalChanging the Source Name DIGITAL AUTO DOLBY DIGITAL DTS SURROUNDMuting the Sound Using the Sleep TimerBasic adjustment auto memory Press SLEEP repeatedlyTuning in to Stations Manually Setting the AM TunerUsing Preset Tuning Receiving Radio BroadcastsWhile listening to an FM station, press FM MODE To tune in a preset stationSelecting the FM Reception Mode AUTO MUTING1 Press QUICK SPEAKER SETUP Basic SettingsQuick Speaker Setup channel number1 Press SETTING Basic Setting ItemsBasic Procedure 3Press in MULTI JOG PUSH SETSetting the Speaker Distance Basic SettingsSetting the Speakers Setting the Bass Sounds¶Low frequency effect attenuator-LFEATTENUATE Selecting the Main or Sub Channel¶Crossover frequency-CROSSOVER ¶Midnight mode-MIDNIGHTMODE¶Virtual Surround Back-VIRTUALSBACK Setting the Digital Input Terminals¶Auto Surround-AUTOSURROUND ¶Digital Input terminal-DIGITALIN1 Press ADJUST Adjusting SoundBasic Adjustment Items Basic ProcedureAdjusting the Speaker Output Levels Adjusting SoundAdjusting the Equalization Patterns ¶ Equalization adjustment-DEQ63HZ, DEQ250HZIntroducing the Surround Modes Using the Surround ModesReproducing Theater Ambience Dolby Digital*1DTS Digital Surround Using the Surround ModesDTS*2 DTS 96/241Select and play any source To cancel the Surround modeActivating the Surround Modes 2Press SURROUND to activate the Surround modeIntroducing the DSP Modes Using the DSP ModesReproducing the Sound Field Digital Acoustic Processor DAP modesAll Channel Stereo To cancel the DSP modeActivating the DSP Modes Mono FilmSound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerDVD player Operating Video ComponentsCD changer EnglishSOLUTION TroubleshootingPROBLEM EnglishOutput Power SpecificationsAmplifier EnglishAM tuner SpecificationsFM tuner IHF GeneralVOLTAGE SELECTOR RX-5052SAUDIO/VIDEO CONTROL RECEIVER CAUTION for mains AC line