JVC 0105RYMMDWJEIN Getting Started, Before Installation, Adjusting the Voltage Selector, English

Page 6
Getting Started

Getting Started

Do not connect the AC power cord until all other connections have been made.

English

This section explains how to connect audio/video components and speakers to the receiver, and how to connect the power supply.

Before Installation

Adjusting the Voltage Selector

General Precautions

Be sure your hands are dry.

Turn the power off to all components.

Read the manuals supplied with the components you are going to connect.

Locations

Install the receiver in a location that is level and protected from moisture and dust.

The temperature around the receiver must be between –5˚C and 35˚C.

Make sure there is good ventilation around the receiver. Poor ventilation could cause overheating and damage the receiver.

Handling the receiver

Do not insert any metal object into the receiver.

Do not disassemble the receiver or remove screws, covers, or cabinet.

Before connections, always do the following first if necessary. Select the correct voltage with the VOLTAGE SELECTOR switch on the rear using a screw driver.

Check to be sure if the voltage mark is set to the voltage for the area where you use this unit.

VOLTAGE SELECTOR

• Do not expose the receiver to rain or moisture.

Checking the Supplied Accessories

220V

Before Installation 110V

127V

Check to be sure you have all of the following items, which are supplied with the receiver.

The number in the parentheses indicates quantity of the pieces supplied.

Remote Control (1)

Batteries (2)

AM Loop Antenna (1)

FM Antenna (1)

AC Plug Adaptor (1)

If anything is missing, contact your dealer immediately.

230 - 240V

Voltage mark

Connecting the FM and AM Antennas

FM antenna connections

Putting Batteries in the Remote Control

Before using the remote control, insert the two supplied batteries first.

1

2 R6(SUM-3)/

3

 

AA(15F)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1Press and slide the battery cover on the back of the remote control.

2Insert the batteries.

• Make sure to match the polarity: (+) to (+) and (–) to (–).

3Replace the cover.

If the remote control cannot transmit signals or operate the receiver correctly, replace the batteries. Use two R6(SUM-3)/AA(15F) type dry-cell batteries.

Note:

Supplied batteries are for the initial setup. Replace for continued use.

CAUTION:

Follow these precautions to avoid leaking or cracking cells:

Place batteries in the remote control so they match the polarity: (+) to (+) and (–) to (–).

Use the correct type of batteries. Batteries that look similar may differ in voltage.

Always replace both batteries at the same time.

Do not expose batteries to heat or flame.

AB

AM

AM

EXT

EXT

AM

AM

LOOP

LOOP

75

ANTENNA

75

ANTENNA

COAXIAL

 

COAXIAL

 

FM

 

FM

 

Extend the supplied FM antenna horizontally.

AM

Adjusting the Voltage SelectorEXT

AM

LOOP

FM Antenna (supplied)

FM 75

 

 

COAXIAL

 

Outdoor FM Antenna Cable

 

ANTENNA

 

(not supplied)

 

 

Connect the supplied FM antenna as temporary measure to the FM 75 COAXIAL terminal—A

If reception is poor, connect the outdoor FM antenna (not supplied)—B

1Disconnect the supplied FM antenna.

2Connect a 75 coaxial cable with the standard type connector

(IEC or DIN45325).

4

Image 6
Contents AUDIO/VIDEO CONTROL RECEIVER EnglishRX-5052S INSTRUCTIONSCaution Proper Ventilation Warnings, Cautions, and OthersCaution--STANDBY/ON button RX-5052SUsing the Surround Modes Table of ContentsAdjusting Sound Using the DSP ModesParts Identification EnglishEnglish Checking the Supplied Accessories Before InstallationAdjusting the Voltage Selector Connecting the FM and AM Antennas2Press and hold the clamp of the speaker terminal Connecting the Speakers and SubwooferConnecting the speakers 3Insert the speaker cordGetting Started Connecting Audio/Video ComponentsConnecting the subwoofer Placing speakersVideo component connections EnglishDVD player Getting Started Connecting the Power CordDigital Connections English3Adjust the volume Daily Operational Procedure1Turn on the power Turning On the PowerOn the remote control Adjusting the VolumeSpeaker and signal indicators on the display Basic OperationsSubwoofer Sound Listening with headphonesTurning On and Off the Selecting the Analog or Digital Input ModeChanging the Display Brightness Attenuating the Input SignalChanging the Source Name DIGITAL AUTO DOLBY DIGITAL DTS SURROUNDMuting the Sound Using the Sleep TimerBasic adjustment auto memory Press SLEEP repeatedlyTuning in to Stations Manually Setting the AM TunerUsing Preset Tuning Receiving Radio BroadcastsWhile listening to an FM station, press FM MODE To tune in a preset stationSelecting the FM Reception Mode AUTO MUTING1 Press QUICK SPEAKER SETUP Basic SettingsQuick Speaker Setup channel number1 Press SETTING Basic Setting ItemsBasic Procedure 3Press in MULTI JOG PUSH SETSetting the Speaker Distance Basic SettingsSetting the Speakers Setting the Bass Sounds¶Low frequency effect attenuator-LFEATTENUATE Selecting the Main or Sub Channel¶Crossover frequency-CROSSOVER ¶Midnight mode-MIDNIGHTMODE¶Virtual Surround Back-VIRTUALSBACK Setting the Digital Input Terminals¶Auto Surround-AUTOSURROUND ¶Digital Input terminal-DIGITALIN1 Press ADJUST Adjusting SoundBasic Adjustment Items Basic ProcedureAdjusting the Speaker Output Levels Adjusting SoundAdjusting the Equalization Patterns ¶ Equalization adjustment-DEQ63HZ, DEQ250HZIntroducing the Surround Modes Using the Surround ModesReproducing Theater Ambience Dolby Digital*1DTS Digital Surround Using the Surround ModesDTS*2 DTS 96/241Select and play any source To cancel the Surround modeActivating the Surround Modes 2Press SURROUND to activate the Surround modeIntroducing the DSP Modes Using the DSP ModesReproducing the Sound Field Digital Acoustic Processor DAP modesAll Channel Stereo To cancel the DSP modeActivating the DSP Modes Mono FilmSound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerDVD player Operating Video ComponentsCD changer EnglishSOLUTION TroubleshootingPROBLEM EnglishOutput Power SpecificationsAmplifier EnglishAM tuner SpecificationsFM tuner IHF GeneralVOLTAGE SELECTOR RX-5052SAUDIO/VIDEO CONTROL RECEIVER CAUTION for mains AC line