JVC rx-8010vbk manual Adjusting the Surround Modes

Page 30
DOLBY SURROUND

Adjusting the Surround Modes

You can also use a Surround mode with a DAP mode (see page 30).

Before you start, remember...

• Make sure that you have set the speaker information correctly

(see page 17).

5.Select the speaker you want to adjust.

•To select the center speaker level, press CENTER. “CTR” appears on the remote control display window.

•To select the left rear speaker level, press REAR L. “REARL” appears on the remote control display window.

•To select the right rear speaker level, press REAR R. “REARR” appears on the remote control display window.

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 3 again.

• You cannot adjust the rear speaker output levels when you have set

“REAR SPK” to “NONE.” See page 17.

• You cannot adjust the center speaker output level and center tone

when you have set “CTR SPK” to “NONE.” See page 17.

• To adjust the front speaker output balance and subwoofer output

level, see pages 16 and 17.

∗CENTER

∗REARL

∗REARR

9

0

+10

FMMODE100+

6.Press LEVEL +/– to adjust the speaker output levels (–10 dB to +10 dB).

+∗BAL L

CH/∗LEVEL

−∗BAL R

From the remote control:

1. Select and play a sound source.

• To enjoy Dolby Pro Logic, play back a software encoded with

Dolby Surround and labeled with

 

 

DOLBY SURROUND

mark.

•To enjoy Dolby Digital, play back a software encoded with Dolby Digital and labeled with D I G I T A L mark.

•To enjoy DTS Digital Surround, play back a software encoded

with DTS Digital Surround and labeled with mark.

2. Press SURROUND ON/OFF to

SURROUND

 

activate an appropriate Surround

ON/OFF

 

mode — PRO LOGIC, DOLBY

 

DIGITAL or DTS SURROUND.

 

The SURROUND ON/OFF lamp on the front panel button lights up.

•Each time you press the button, the Surround mode turns on and off alternately.

•When “PRO LOGIC” is selected, the PRO LOGIC indicator lights up on the display.

7.

Press SOUND.

SOUND

 

• To adjust other speaker output levels, repeat

 

 

steps 5 and 6.

 

8.

Press TEST again to stop the test

TEST

4

 

tone.

 

 

9.

Press CTR TONE to select the

CTRTONE

 

center tone level you want.

5

ENTER

The center tone adjustment affects the mid- frequency range, which the human voice is mostly made up of.

•Each time you press the button, the display changes to show the following:

CTR TONE 1 CTR TONE 2 CTR TONE 3

(Softer)(Soft)(Flat)

CTR TONE 5

 

CTR TONE 4

 

(Sharper)

 

(Sharp)

To make the dialogue softer, select “CTR TONE 1” or “CTR

3. Press SOUND.

The 10 keys are activated for sound adjustments.

4. Press TEST to check the speaker output balance.

“TEST TONE L” starts flashing on the display, and a test tone comes out of the speakers in the following order:

SOUND

TEST

4

TONE 2.”

To make the dialogue clearer, select “CTR TONE 4” or “CTR TONE 5.”

When “CTR TONE 3” is selected, no adjustment is applied.

On the front panel:

You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.

 

TEST TONE L

 

TEST TONE C

 

TEST TONE R

 

 

(Left front speaker)

(Center speaker)

(Right front speaker)

 

 

TEST TONE LS

 

 

TEST TONE RS

 

 

(Left rear speaker)

 

 

(Right rear speaker)

 

 

Notes:

•You can adjust the speaker output levels without outputting the test tone.

•No test tone comes out of the center speaker when “CTR SPK” is set to “NONE” (see page 17).

•No test tone comes out of the rear speakers when “REAR SPK” is set to “NONE” (see page 17).

•If the TV is turned on and the proper video input is selected on the TV, the test tone screen will appear on the TV.

1. Select and play a sound source.

• To enjoy Dolby Pro Logic, play back a software encoded with

Dolby Surround and labeled with mark.

•To enjoy Dolby Digital, play back a software encoded with Dolby Digital and labeled with D I G I T A L mark.

•To enjoy DTS Digital Surround, play back a software encoded

with DTS Digital Surround and labeled with mark.

27

Page 29 Page 31
Image 30
Page 29 Page 31
Contents RX-8010VBK Mises en garde, précautions et indications diverses For Canada/pour Le Canada Table of Contents CATV/DBS, VCR 1, TV, Audio Remote Control Front PanelParts Identification USB AUDIO, FM/AMConnecting the FM and AM Antennas Before InstallationChecking the Supplied Accessories Getting StartedConnecting the front speakers Connecting the SpeakersBasic connecting procedure AM Antenna ConnectionsConnecting the subwoofer speaker Connecting Audio/Video ComponentsConnecting the rear and center speakers Analog ConnectionsVCRs Cassette deck or MD recorderVideo component connections CD recorderTV and/or DBS tuner Video camera DVD playerDBS tuner Digital Connections Digital input terminalsDigital output terminal Lamp on the USB Audio button lights up Change the PC audio settingUSB Connection USB cablePlug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control Replace the coverBasic Operations Turning the Power On and Off StandbyBefore using the remote control Selecting the Source to PlayAdjusting the Volume Signal and speaker indicators on the displaySelecting different sources for picture and sound Selecting the Front Speakers Muting the Sound Listening at Night Midnight ModeFrom the remote control only On the front panel onlyActivating the Subwoofer Sound Attenuating the Input Signal Reinforcing the BassSelecting the Line Direct Function Adjusting the Equalization Patterns Using the Sleep TimerRecording a Source Selecting the Video Input Terminal Basic SettingsAdjusting the Front Speaker Output Balance Changing the Source NameSetting the Subwoofer Information Adjusting the Subwoofer Output LevelSetting the Speakers for a Surround Field Center speaker output from 0 ms to 5 ms CTR Delay Center Delay Appears on the displayTo select the delay time 15 msDigital Input Digital in Terminal Setting Selecting the Analog or Digital Input Mode Showing the Text Information on Display Basic Setting and Adjustment Auto MemoryTo store the volume level To turn on the One Touch OperationTuning in Stations Manually Using Preset Tuning Receiving Radio BroadcastsPress FM Mode Press FM/AM Preset 5/untilSelecting the FM Reception Mode Press FM/AMCreating a Surround Field in Your Room Surround modesDSP modes Reproducing the Sound Field DVD Multi Playback ModeHeadphone DSP mode 3D-PHONIC modesAvailable DSP Modes According to the Speaker Arrangement Available DSP modesAdjusting the Surround Modes Adjust the speaker output levels Adjust the center toneAdjusting the DAP Modes Press DSP Mode repeatedly until Adjust the room size sense of spaciousnessAdjust the liveness DAP mode you want to adjustOutput balance Press Liveness to adjust the liveness. LivenessAdjusting the Surround Modes with DAP Modes Speaker output levels -10 dB toPress Liveness to adjust Liveness Adjust the speaker output levelsCenter Press DSP Mode repeatedly until Mode Adjusting the 5 CH/4 CH Stereo ModePress DSP Mode repeatedly until DSP Mode OnlyAdjust the center speaker output level CH Stereo mode onlyAdjusting the 3D-PHONIC Modes Center tone level you want forPress Center to select the center Adjust the overall levels of the effect3D Action or 3D Digital SpeakerPress DVD Multi so that DVD Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Multi appears on the displayUsing the On-Screen Menus Press MenuThen press 2 Press 5 / to move to Sound CONTROL, then press 2Press 5 / to move to Digital EQ CONTROL, then press 2Select DVD Multi as the playing source Press 5/ to move to Effect ADJUST, then press 2Press 5/ to move To Level ADJUST, then press 2 Press 5/ to move to Sound CONTROL, then press 2Press 5/ to move to Tuner CONTROL, then press 2 Press 5/ to move To Preset MEMORY, then press 2Select FM or AM as the playing source Menu disappears from the TVSetting 2 menu Press 5 / to move To Setting Then press 2Setting the Basic Setting Items Setting 1 menuSame time Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionDisplaying the Disc Information on the TV screen Text Compu Link Remote Control SystemCD player MD recorder Disc Search Only for CD PlayerTo exit from the Disc information screen Press Text Display while CD or MD is selected as the sourceShowing the Disc Information on the TV Screen Press ExitPress 5 / to move To Performer Then press SET Press Text Display while CD is selected as the sourcePress 5 / to move to SEARCH, then Press SET Press SET againSearch for a disc by its genre Press 5/ to move to Title Input Then press SETEntering the Disc Information For the CD Player with the disc memory functionMove to Disc Michael in this Example, then press SET Press 5/ / 2/ 3toPress Text Display while MD is selected as the source Press 5/ to moveConnections 2 Video Cable Connection AV Compu Link Remote Control SystemConnections 1 AV Compu Link Connection VCROne-Touch Video Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch DVD PlayTuner Operating JVC’s Audio/Video ComponentsOperating Audio Components Sound control section AmplifierCassette deck CD changerCD recorder TurntableOperating Video Components VCR 1 VCR connected to the VCR 1 jacksDVD player If there are more than one code listed for your brand of TV Release TV PowerTry to operate your TV by pressing TV Power Operating Other Manufacturers’ Video EquipmentRelease CATV/DBS Power Release VCR 1 PowerTry to operate your VCR by pressing VCR 1 Power Release Audio Power Troubleshooting Problem Possible Cause SolutionRemove the obstruction Audio SpecificationsAmplifier VideoAM tuner Tuning Range Usable Sensitivity Signal-to-Noise RatioFM tuner IHF General781 954 650 Valley Road Wayne, NJ1099 Limited Warranty AUDIO-2 JVC 0101NHMMDWJEIN
Related manuals
Manual 64 pages 41.74 Kb
Top Page Image Contents