JVC rx-8010vbk manual Connecting Audio/Video Components, Connecting the rear and center speakers

Page 8

Connecting the rear and center speakers

Connect rear speakers to the REAR SPEAKERS terminals and a center speaker to the CENTER SPEAKER terminals.

Center speaker

CENTER

REAR SPEAKERS

SPEAKER

+

+

Analog Connections

Audio component connections

Use the cables with RCA pin plugs (not supplied).

Connect the white plug to the audio left jack, and the red plug to the audio right jack.

CAUTION:

If you connect a sound-enhancing device such as a graphic equalizer between the source components and this receiver, the sound output through this receiver may be distorted.

 

RIGHT

LEFT

 

CAUTION : SPEAKER IMPEDANCE 8

16

Right rear speaker

 

Left rear speaker

Connecting the subwoofer speaker

You can enhance the bass by connecting a subwoofer. Connect the input jack of a powered subwoofer to the SUBWOOFER OUT jack on the rear panel, using a cable with RCA pin plugs (not supplied).

SUBWOOFER

OUT

Powered subwoofer

Connecting Audio/Video Components

Turntable

Turntable

To audio output

If an earth cable is provided for your turntable, connect the cable to the screw marked (H) on the rear panel.

Ex.: This connection is for the turntable with an MM (moving- magnet) type cartridge.

Note:

RIGHT LEFT AUDIO

REAR

PHONO

CD

OUT

(REC)

TAPE

MD

IN

(PLAY)

OUT

(REC)

CDR

IN

(PLAY)

You can connect the following audio/video components to this receiver. Refer also to the manuals supplied with your components.

Any turntables incorporating a small-output cartridge such as an MC (moving-coil) type must be connected to this receiver through a commercial head amplifier or step-up transformer. Direct connection may result in insufficient volume.

Audio Components

Video Components

• Turntable

• DVD player*

• CD player*

• TV*

 

 

• Cassette deck or

• DBS tuner*

MD recorder*

• VCR(s)

• CD recorder*

• Video camera

Personal computer (PC)

*You can connect these components using the methods described in “Analog connections” (to the right), or in “Digital connections” (see page 8).

CD player

CD player

To audio output

RIGHT LEFT AUDIO

REAR

PHONO

CD

OUT

(REC)

TAPE

MD

IN

(PLAY)

OUT

(REC)

CDR

IN

(PLAY)

5

Image 8
Contents RX-8010VBK Mises en garde, précautions et indications diverses For Canada/pour Le Canada Table of Contents Remote Control Front Panel Parts IdentificationCATV/DBS, VCR 1, TV, Audio USB AUDIO, FM/AMBefore Installation Checking the Supplied AccessoriesConnecting the FM and AM Antennas Getting StartedConnecting the Speakers Basic connecting procedureConnecting the front speakers AM Antenna ConnectionsConnecting Audio/Video Components Connecting the rear and center speakersConnecting the subwoofer speaker Analog ConnectionsCassette deck or MD recorder Video component connectionsVCRs CD recorderDBS tuner TV and/or DBS tuner Video cameraDVD player Digital output terminal Digital ConnectionsDigital input terminals Change the PC audio setting USB ConnectionLamp on the USB Audio button lights up USB cableConnecting the Power Cord Putting Batteries in the Remote ControlPlug the power cord into an AC outlet Replace the coverTurning the Power On and Off Standby Before using the remote controlBasic Operations Selecting the Source to PlaySelecting different sources for picture and sound Adjusting the VolumeSignal and speaker indicators on the display Listening at Night Midnight Mode From the remote control onlySelecting the Front Speakers Muting the Sound On the front panel onlySelecting the Line Direct Function Activating the Subwoofer Sound Attenuating the Input SignalReinforcing the Bass Recording a Source Adjusting the Equalization PatternsUsing the Sleep Timer Basic Settings Adjusting the Front Speaker Output BalanceSelecting the Video Input Terminal Changing the Source NameSetting the Speakers for a Surround Field Setting the Subwoofer InformationAdjusting the Subwoofer Output Level CTR Delay Center Delay Appears on the display To select the delay timeCenter speaker output from 0 ms to 5 ms 15 msDigital Input Digital in Terminal Setting Selecting the Analog or Digital Input Mode Basic Setting and Adjustment Auto Memory To store the volume levelShowing the Text Information on Display To turn on the One Touch OperationTuning in Stations Manually Using Preset Tuning Receiving Radio BroadcastsPress FM/AM Preset 5/until Selecting the FM Reception ModePress FM Mode Press FM/AMDSP modes Creating a Surround Field in Your RoomSurround modes DVD Multi Playback Mode Headphone DSP modeReproducing the Sound Field 3D-PHONIC modesAvailable DSP Modes According to the Speaker Arrangement Available DSP modesAdjusting the Surround Modes Adjusting the DAP Modes Adjust the speaker output levelsAdjust the center tone Adjust the room size sense of spaciousness Adjust the livenessPress DSP Mode repeatedly until DAP mode you want to adjustPress Liveness to adjust the liveness. Liveness Adjusting the Surround Modes with DAP ModesOutput balance Speaker output levels -10 dB toCenter Press Liveness to adjustLiveness Adjust the speaker output levels Adjusting the 5 CH/4 CH Stereo Mode Press DSP Mode repeatedly until DSP ModePress DSP Mode repeatedly until Mode OnlyCH Stereo mode only Adjusting the 3D-PHONIC ModesAdjust the center speaker output level Center tone level you want forAdjust the overall levels of the effect 3D Action or 3D DigitalPress Center to select the center SpeakerUsing the DVD Multi Playback Mode Activating the DVD Multi Playback ModePress DVD Multi so that DVD Multi appears on the displayUsing the On-Screen Menus Press MenuPress 5 / to move to Sound CONTROL, then press 2 Press 5 / to move to Digital EQThen press 2 CONTROL, then press 2Press 5/ to move to Effect ADJUST, then press 2 Press 5/ to move To Level ADJUST, then press 2Select DVD Multi as the playing source Press 5/ to move to Sound CONTROL, then press 2Press 5/ to move To Preset MEMORY, then press 2 Select FM or AM as the playing sourcePress 5/ to move to Tuner CONTROL, then press 2 Menu disappears from the TVPress 5 / to move To Setting Then press 2 Setting the Basic Setting ItemsSetting 2 menu Setting 1 menuCompu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverSame time Automatic Source SelectionText Compu Link Remote Control System CD player MD recorderDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerPress Text Display while CD or MD is selected as the source Showing the Disc Information on the TV ScreenTo exit from the Disc information screen Press ExitPress Text Display while CD is selected as the source Press 5 / to move to SEARCH, then Press SETPress 5 / to move To Performer Then press SET Press SET againPress 5/ to move to Title Input Then press SET Entering the Disc InformationSearch for a disc by its genre For the CD Player with the disc memory functionPress 5/ / 2/ 3to Press Text Display while MD is selected as the sourceMove to Disc Michael in this Example, then press SET Press 5/ to moveAV Compu Link Remote Control System Connections 1 AV Compu Link ConnectionConnections 2 Video Cable Connection VCRAutomatic Selection of TV’s Input Mode Automatic Power On/OffOne-Touch Video Play One-Touch DVD PlayOperating JVC’s Audio/Video Components Operating Audio ComponentsTuner Sound control section AmplifierCD changer CD recorderCassette deck TurntableDVD player Operating Video ComponentsVCR 1 VCR connected to the VCR 1 jacks Release TV Power Try to operate your TV by pressing TV PowerIf there are more than one code listed for your brand of TV Operating Other Manufacturers’ Video EquipmentTry to operate your VCR by pressing VCR 1 Power Release CATV/DBS PowerRelease VCR 1 Power Release Audio Power Troubleshooting Problem Possible Cause SolutionRemove the obstruction Specifications AmplifierAudio VideoTuning Range Usable Sensitivity Signal-to-Noise Ratio FM tuner IHFAM tuner General1099 781 954 650Valley Road Wayne, NJ Limited Warranty AUDIO-2 JVC 0101NHMMDWJEIN
Related manuals
Manual 64 pages 41.74 Kb