JVC rx-8010vbk manual Specifications, Amplifier, Audio, Video

Page 60

Specifications

Amplifier

Output Power:

At Stereo operation:

Front channels:

120 W per channel, min. RMS, driven into 8 Ω, 20

Hz to 20 kHz with no more than 0.08% total harmonic distortion.

At Surround operation:

 

Front channels:

100 W per channel, min. RMS, driven into 8 Ω at 1 kHz with no

 

more than 0.8% total harmonic distortion.

Center channel:

100 W, min. RMS, driven into 8 Ω at 1 kHz, with no more than

 

0.8% total harmonic distortion.

Rear channels:

100 W per channel, min. RMS, driven into 8 Ω at 1 kHz, with no

 

more than 0.8% total harmonic distortion.

Audio

 

 

2.5 mV/47 kΩ

 

Audio Input Sensitivity/Impedance (1 kHz):

PHONO (MM):

 

 

 

DVD, VCR 1, VCR 2, VIDEO, TV SOUND/DBS, CD, CDR, TAPE/MD:

 

 

 

200 mV/47 kΩ

 

 

Audio Input (DIGITAL IN)* :

Coaxial: DIGITAL 1 (DVD):

0.5 V(p-p)/75 Ω

 

 

 

Optical: DIGITAL 2 (CD), DIGITAL 3 (TV), DIGITAL 4 (CDR):

 

 

 

–21 dBm to –15 dBm (660 nm ±30 nm)

 

 

*Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround (with

 

 

sampling frequency — 32 kHz, 44.1 kHz, 48 kHz).

 

 

 

USB: Revision 1.0, full-speed (with sampling frequency — 32

kHz, 44.1 kHz, 48 kHz)

 

Audio Output Level:

VCR 1, VCR 2, CDR, TAPE/MD:

200 mV

 

 

Digital output:

Optical: DIGITAL OUTPUT:

Signal wave length: 660 nm

 

 

 

Output level: –21 dBm to –15 dBm

Signal-to-Noise Ratio (’66 IHF/’78 IHF):

PHONO (MM):

70 dB/78 dB (at REC OUT)

 

 

DVD, VCR 1, VCR 2, VIDEO, TV SOUND/DBS, CD, CDR, TAPE/MD:

 

 

 

92 dB/80 dB (LINE DIRECT ON)

 

Frequency Response (8 Ω):

PHONO:

20 Hz to 20 kHz (±1 dB)

 

 

DVD, VCR 1, VCR 2, VIDEO, TV SOUND/DBS, CD, CDR, TAPE/MD:

 

 

 

20 Hz to 100 kHz (+1 dB, –3 dB)

 

 

USB:

20 Hz to 20 kHz (+1 dB, –3 dB)

 

RIAA Phono Equalization:

±1.0 dB (20 Hz to 20 kHz)

 

 

 

Bass boost:

+6 dB ±1.0 dB at 100 Hz

 

 

Video

 

 

 

 

 

Video Input Sensitivity/Impedance:

 

 

1 V(p-p)/75 Ω

 

Composite video:

DVD, VCR 1, VCR 2, VIDEO, TV SOUND/DBS:

 

S-video:

DVD, VCR 1, VCR 2, VIDEO, TV SOUND/DBS:

 

 

 

 

(Y: luminance):

1 V(p-p)/75 Ω

 

 

 

(C: chrominance, burst):

0.286 V(p-p)/75 Ω

 

Component video:

DVD, DBS:

(Y: luminance):

1 V(p-p)/75 Ω

 

 

 

(PB, PR):

0.7 V(p-p)/75 Ω

 

Video Output Level:

 

 

 

 

Composite video:

VCR 1, VCR 2, MONITOR OUT:

 

1 V(p-p)/75 Ω

 

S-video:

VCR 1, VCR 2, MONITOR OUT:

(Y: luminance):

1 V(p-p)/75 Ω

 

 

 

(C: chrominance, burst):

0.286 V(p-p)/75 Ω

 

Component video:

MONITOR OUT:

(Y: luminance):

1 V(p-p)/75 Ω

 

 

 

(PB, PR):

0.7 V(p-p)/75 Ω

 

Synchronization:

Negative

 

 

 

Signal-to-Noise Ratio:

45 dB

 

 

57

On-Screen Color System:

NTSC

 

 

 

 

 

 

Image 60
Contents RX-8010VBK Mises en garde, précautions et indications diverses For Canada/pour Le Canada Table of Contents Remote Control Front Panel Parts IdentificationCATV/DBS, VCR 1, TV, Audio USB AUDIO, FM/AMBefore Installation Checking the Supplied AccessoriesConnecting the FM and AM Antennas Getting StartedConnecting the Speakers Basic connecting procedureConnecting the front speakers AM Antenna ConnectionsConnecting Audio/Video Components Connecting the rear and center speakersConnecting the subwoofer speaker Analog ConnectionsCassette deck or MD recorder Video component connectionsVCRs CD recorderTV and/or DBS tuner Video camera DVD playerDBS tuner Digital Connections Digital input terminalsDigital output terminal Change the PC audio setting USB ConnectionLamp on the USB Audio button lights up USB cableConnecting the Power Cord Putting Batteries in the Remote ControlPlug the power cord into an AC outlet Replace the coverTurning the Power On and Off Standby Before using the remote controlBasic Operations Selecting the Source to PlayAdjusting the Volume Signal and speaker indicators on the displaySelecting different sources for picture and sound Listening at Night Midnight Mode From the remote control onlySelecting the Front Speakers Muting the Sound On the front panel onlyActivating the Subwoofer Sound Attenuating the Input Signal Reinforcing the BassSelecting the Line Direct Function Adjusting the Equalization Patterns Using the Sleep TimerRecording a Source Basic Settings Adjusting the Front Speaker Output BalanceSelecting the Video Input Terminal Changing the Source NameSetting the Subwoofer Information Adjusting the Subwoofer Output LevelSetting the Speakers for a Surround Field CTR Delay Center Delay Appears on the display To select the delay timeCenter speaker output from 0 ms to 5 ms 15 msDigital Input Digital in Terminal Setting Selecting the Analog or Digital Input Mode Basic Setting and Adjustment Auto Memory To store the volume levelShowing the Text Information on Display To turn on the One Touch OperationTuning in Stations Manually Using Preset Tuning Receiving Radio BroadcastsPress FM/AM Preset 5/until Selecting the FM Reception ModePress FM Mode Press FM/AMCreating a Surround Field in Your Room Surround modesDSP modes DVD Multi Playback Mode Headphone DSP modeReproducing the Sound Field 3D-PHONIC modesAvailable DSP Modes According to the Speaker Arrangement Available DSP modesAdjusting the Surround Modes Adjust the speaker output levels Adjust the center toneAdjusting the DAP Modes Adjust the room size sense of spaciousness Adjust the livenessPress DSP Mode repeatedly until DAP mode you want to adjustPress Liveness to adjust the liveness. Liveness Adjusting the Surround Modes with DAP ModesOutput balance Speaker output levels -10 dB toPress Liveness to adjust Liveness Adjust the speaker output levelsCenter Adjusting the 5 CH/4 CH Stereo Mode Press DSP Mode repeatedly until DSP ModePress DSP Mode repeatedly until Mode OnlyCH Stereo mode only Adjusting the 3D-PHONIC ModesAdjust the center speaker output level Center tone level you want forAdjust the overall levels of the effect 3D Action or 3D DigitalPress Center to select the center SpeakerUsing the DVD Multi Playback Mode Activating the DVD Multi Playback ModePress DVD Multi so that DVD Multi appears on the displayUsing the On-Screen Menus Press MenuPress 5 / to move to Sound CONTROL, then press 2 Press 5 / to move to Digital EQThen press 2 CONTROL, then press 2Press 5/ to move to Effect ADJUST, then press 2 Press 5/ to move To Level ADJUST, then press 2Select DVD Multi as the playing source Press 5/ to move to Sound CONTROL, then press 2Press 5/ to move To Preset MEMORY, then press 2 Select FM or AM as the playing sourcePress 5/ to move to Tuner CONTROL, then press 2 Menu disappears from the TVPress 5 / to move To Setting Then press 2 Setting the Basic Setting ItemsSetting 2 menu Setting 1 menuCompu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverSame time Automatic Source SelectionText Compu Link Remote Control System CD player MD recorderDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerPress Text Display while CD or MD is selected as the source Showing the Disc Information on the TV ScreenTo exit from the Disc information screen Press ExitPress Text Display while CD is selected as the source Press 5 / to move to SEARCH, then Press SETPress 5 / to move To Performer Then press SET Press SET againPress 5/ to move to Title Input Then press SET Entering the Disc InformationSearch for a disc by its genre For the CD Player with the disc memory functionPress 5/ / 2/ 3to Press Text Display while MD is selected as the sourceMove to Disc Michael in this Example, then press SET Press 5/ to moveAV Compu Link Remote Control System Connections 1 AV Compu Link ConnectionConnections 2 Video Cable Connection VCRAutomatic Selection of TV’s Input Mode Automatic Power On/OffOne-Touch Video Play One-Touch DVD PlayOperating JVC’s Audio/Video Components Operating Audio ComponentsTuner Sound control section AmplifierCD changer CD recorderCassette deck TurntableOperating Video Components VCR 1 VCR connected to the VCR 1 jacksDVD player Release TV Power Try to operate your TV by pressing TV PowerIf there are more than one code listed for your brand of TV Operating Other Manufacturers’ Video EquipmentRelease CATV/DBS Power Release VCR 1 PowerTry to operate your VCR by pressing VCR 1 Power Release Audio Power Troubleshooting Problem Possible Cause SolutionRemove the obstruction Specifications AmplifierAudio VideoTuning Range Usable Sensitivity Signal-to-Noise Ratio FM tuner IHFAM tuner General781 954 650 Valley Road Wayne, NJ1099 Limited Warranty AUDIO-2 JVC 0101NHMMDWJEIN
Related manuals
Manual 64 pages 41.74 Kb