ProSpot Fitness PC-1000 manual STEP#2 Sensorweightbar Installation

7.Attachthetwo RearSupportFrames(4)to thetwo baserails(1 & 2) usingfour bolts(22),eightwashers(18) andfour nuts(20)as shown.HANDTIGHTENthe boltsat thistime.

8.Attachthe two PulleySupportFrames(17)to the RearSupportFrames(4) andthe UprightGuidePosts(10 & 12) usingeightbolts(28),sixteenwashers(18)and eightnuts(20)as shown.HANDTIGHTENthe bolts at thistime .

9.Attachthe UpperCrossBrace(11)to the two RearSupportFrames(4) usingfourbolts(51),eightwashers (18)andfournuts(20)as shown.HANDTIGHTENthe boltsat thistime.

'10.for assemblyin previoussteps. Tightenall bolts and nuts used

11.Carefullyinsertthe LeftWeightBar Knuckle(44) up throughthe rectangularcutoutin the PulleySupport Frame(17)andflex the LeftWeightBar Cables(24)ontothe pulleys(27)so thatthe cablesinsertintothe groovesof eachcorrespondingpulleysandallowingthe LeftWeightBar Knuckle(44)to hangfree.Be sure that the cablesare straight and uncrossedand cablesand pulleysmove smoothly.

12.Repeatthestep11 on the rightsideof the PROSPOT/nsssrMPC-1000.

STEP#2: SENSORWEIGHTBAR INSTALLATION

1.Standingin frontof the PROSPOTlrressrMPC-1000.Insertone end and thenthe otherend of the Sensor WeightBar (25)intothe Knuckles(42 & 44).Slidethe knucklesontothe Bar untiltheyrestsnuglyagainst the preinstalledsensorretainingcollars(45 & 48) at eachend of the SensorWeightBar (25).(Thereis a rotationlimi{ingpin that protrudesfrom the bottomof the SensorWeight Bar (25)that mustfit througha slot in the knucklesg? A 44tas it is slidintoposition).

2.Placeone PlasticLockingSleeve(39)ontoeachendof the SensorWeightBar(25)andslidetheminwards untiltheybuttup againstandsecuretheWeightBarCableKnucklein place.TightenPlasticLockingSleeve boltssecurely.

3.Placeone of the OlympicAdapters(30)ontothe SensorWeightBar (25)and slidethemontothe Bar until theytouchthe PlasticLockingSleeves(39).Insertan OlympicAdapterRetainingPlug(33)ontoeachend of the SensorWeightBar (25)so thatthey also go insideof the OlympicAdapters(30).Securewith two Allenbolts(29),twowashers(36)andtwo springwashers(56).

4.Attachthe four smallplasticpipes(15)to the two PulleySupportFrames(17) usingfour bolts(34),eight washers(38)andfournuts(35)as shown.Tightenthe boltssecurely.

5.Attachthe six SideWeightPlateHolders(14)to the two RearSupportFrames(4) usingtwelvebolts(53), twenty-fourwashers(18)andtwelvenuts(20)as shown.Tightenthe boltssecurely.

6.Carefullythreadthe rear ends of the Cross BraceWire Harness(8) throughthe middlehole on the ElectronicBox LocatingPlate(13)and then attachthe LocatingPlate(13)to the LowerCrossBrace(3) usingtwo bolts(22),fourwashers(18)andtwo nuts(20).Tightenthe boltssecurely.

7.Attachthe ElectronicBox ProtectingCover(5) to the LocatingPlate(13)usingtwo crossscrews(52)and lwo washers(57)as shown.Tightenthe screwssecurely.

Note:In this manualwhenreferringto Leftand Rightsideof unit,the leftand rightperspective arefrom the outside,facingthe front of the unit.

--2--