ProSpot Fitness P-600 manual Step #6 Cable Installation

Page 5

7.Place Side Weight Stack Covers (73) so that the holes on the cover align with the holes on the tabs of the Upper Frame and bottom Side Base Rails (6,7). Secure with bolts #113, flat washers #136 and nuts #130.

8.Install jam nuts (103) onto threaded portion of each Weight Stack Pulley Bracket (101). Rotate the nut until ¾” of the thread is exposed. Now install Weight Stack Pulley Brackets (101) to the top plate of the weight stacks (98). Turn each Weight Stack Pulley Bracket until it hits the jam nut (103).

9.Install small, Single-Groove Pulley (33) into each Weight Stack Pulley Bracket (101) and secure each with bolt #109, flat washer #134 and lock nut #129.

10.Make sure all pulley bolts are tight.

STEP #6 – CABLE INSTALLATION

1.If ball and bracket assemblies are attached to cables, disassemble and set aside.

2.Begin by screwing Side Weight Stack Cable (102) into Cable Head Slider Frame (15,16) one-half inch (½”).

3.For each left and right cable installation perform the following steps: Thread Side Weight Stack Cable (102) over the two pulleys in the Upper Frame (8,9), then down and underneath the Weight Stack Pulley and back up over the remaining two Upper Frame pulleys and then down to the pulley on the side Base Rail (6,7).

Next, thread the cable through the holes in the weight stack support frame on the lower base rails, then underneath the pulley in the Front Guide Post (1,2). Go over top the large pulley in the Cable Head Slider Frame then between the two small pulleys in the Cable Head Slider Frame (15,16). (See Diagram.)

4.Once cable is through the two small pulleys in the Cable Head Slider Frame (15,16), install ball and bracket assembly onto the end of the cable: Slide hard, black, plastic ball into cable end and slide round ball tip of cable into u-shaped bracket. Place Link Ring (158) into u-shaped bracket and secure assembly with bolt and nut supplied.

NOTE: Be sure that the cables are in the groove of each Pulley and that the Cable and Pulleys move smoothly.

STEP #7 – ELECTRONIC BOX INSTALLATION

If installing optional PHL-60, see PHL-60 instructions for Electronic Box Installation. If not installing optional PHL- 60, follow instructions below:

1.Place Electronic Box Locating Board (76) behind Back Base Rail (13). Pull Base Rail Wire Harness (143) through the Electronic Box Locating Board (76). Align Electronic Box Locating Board (76) with pre-drilled holes in the Back Base Rail (13). Secure with two of each bolt #106, flat washer #133 and lock nut #128.

2.Place Electronic Box (77) onto Electronic Box Locating board (76). Plug wire harness (143) into Electronic Box (77) so that the indicating lights are upwards and the plug is facing backward. Push excess wire into Back Base Rail (13).

3.Install Protective Cover (78) and secure with two screws #121.

4.Plug one end of the power supply into wall receptacle and the other end into the Electronic Box (77). The indicating lights of the Electronic Box (77) should blink green, showing there is power to it. When sensors are activated, a steady red light will also come on.

Note: Rear Cover For Optional Weight Stack (151) will only be used if PHL-60 is installed. If PHL-60 is being installed, attach the Rear Cover for Optional Weight Stack (151) using the following instructions:

1.Install Rear Cover Link Plate (154) by aligning holes with Back Base Rail (13) and secure with bolt #112, two flat washers #136 and lock nut #130.

2.Place the Rear Cover For Optional Weight Stack (151) so that the upper holes align with the holes in the Back Top Rail (11). Secure with bolt #112, two flat washers #136 and lock nut #130.

3.Secure bottom portion of Rear Cover (151) to the Link Plate (154), using bolt #113, two flat washers #136 and lock nut #130.

--5--

Image 5
Contents PROSPOTfitness Model P-600 Instructions for Assembly of the ProSpotfitness P-600 Instructions for Assembly of the ProSpotfitness P-600 Step #2 Sensor Weight BAR Installation Step #6 Cable Installation Main Frame Assembly Main Frame Assembly Sensor Weight BAR Installation Electronic BOX Installation Cable Head Parts Diagram Spot Block Parts Diagram Weight Bar-Cable Knuckle Assembly & Trouble Shooting Diagram Read!! This Page Before Using Your ProSpotfitness Product User Instructions for the P-600 User Instructions for the P-600 Using Cable Crossover Sample Exercise List Maintenance Program ProSpotfitness PHL-600 Parts list Side Weight Stack Pulley Bracket Trouble Shooting of ProSpot Systems Trouble Shooting Warranty & Contact Information

P-600 specifications

ProSpot Fitness has gained a reputation in the fitness community for its innovative approach to strength training, and the P-600 model is a standout in their collection. This remarkable piece of fitness equipment combines effective engineering with user-friendly design, making it suitable for both seasoned athletes and casual gym-goers alike.

At the core of the P-600 is its versatile multi-station functionality. With this single machine, users can perform a wide range of exercises, targeting various muscle groups. The P-600 allows for exercises such as bench press, leg press, squats, and more, offering an all-in-one solution for strength training. This versatility is especially beneficial for those with limited space, as it eliminates the need for multiple pieces of equipment.

One of the standout features of the P-600 is its robust construction. Built with high-quality steel, this machine is designed to withstand rigorous workouts without compromising stability or safety. The sturdy frame and base provide users with a solid foundation, allowing them to push their limits without fear of equipment failure.

The P-600 also incorporates advanced technology to enhance the workout experience. Its adjustable weight system allows users to quickly and easily modify resistance levels, accommodating individual fitness levels and goals. This feature makes it ideal for progressive training, as users can gradually increase their weights as they become stronger.

Another key characteristic of the P-600 is its ergonomic design. The machine features padded seats and backrests, ensuring comfort during extended workout sessions. Adjustable components cater to a wide range of body types, allowing users to find the perfect fit for their exercises.

Safety is a significant consideration for ProSpot Fitness, and the P-600 exemplifies this commitment. Equipped with safety locks and mechanisms, users can perform exercises with confidence, knowing they are safeguarded from potential accidents.

In conclusion, the ProSpot Fitness P-600 is a revolutionary multi-station strength training machine. Its versatility, robust construction, advanced weight adjustment technology, ergonomic design, and safety features make it an excellent choice for anyone looking to elevate their fitness routine. Whether you're setting up a home gym or enhancing your commercial facility, the P-600 is a worthy investment that will help users achieve their fitness goals effectively and efficiently.