Eiki LC-X50 Connecting Projector, Terminals of Projector, Computer Input 2/MONITOR Output

Page 12

CONNECTING PROJECTOR

TERMINALS OF PROJECTOR

This projector has input and output terminals on its back for connecting computers and video equipment. Refer to figures on pages 12 to 14 and connect properly.

COMPUTER AUDIO INPUT 2/ AUDIO MONITOR OUTPUT JACK

This terminal is switchable and can be used as computer audio input 2 or audio monitor output (variable).

Set the terminal up as either Computer audio input 2 or Audio Monitor output properly before using this terminal. (Refer to P13, P23.)

COMPUTER INPUT 1 (ANALOG HDB 15-pin)

TERMINAL

Connect computer output to this terminal. (Refer to P13.)

COMPUTER AUDIO

INPUT 1 JACK

Connect an audio output (stereo) from computer to this jack.

(Refer to P13.)

R/C JACK

When using Wired/Wireless Remote Control Unit as Wired Remote Control, Connect Wired Remote Control Unit to this jack with Remote Control Cable (supplied).

COMPUTER INPUT 2/MONITOR OUTPUT

 

 

 

 

CONTROL PORT CONNECTOR

 

 

 

 

When controlling computer

(ANALOG HDB 15-pin) TERMINAL

 

 

 

 

 

This terminal is switchable and can

INPUT 1

AUDIO 1

 

R/C JACK

with Remote Control Unit of

 

 

this projector, connect mouse

be used as computer input or monitor

 

 

 

 

 

 

RESET

port of your personal computer

output. Set the terminal up as either

 

 

 

 

INPUT 2 / OUT

 

CONTROL PORT

to this connector. (Refer to

Computer input or Monitor output

 

AUDIO 2

properly before using this terminal.

 

 

 

 

P13.)

 

 

 

 

 

Refer to P13, P23.)

 

INPUT 3

R – AUDIO 3 – L

USB

USB CONNECTOR (Series B)

Note; This terminal outputs from

 

 

 

 

COMPUTER INPUT 1 jacks only.

 

VIDEO/Y – Cb/Pb – Cr/Pr

 

(MONO)

 

When controlling computer

 

 

INPUT 4

R – AUDIO 4 – L

S–VIDEO

with Remote Control Unit of

 

 

 

 

 

 

this projector, connect USB

VIDEO INPUT JACKS

 

VIDEO/Y – Cb/Pb – Cr/Pr

 

(MONO)

 

terminal of your personal

 

 

 

 

 

computer to this terminal.

(INPUT 3 and INPUT 4)

 

 

 

 

 

(Refer to P13.)

Connect composite video

 

 

 

 

 

S-VIDEO INPUT JACK

output from video equipment

 

RESET BUTTON

 

 

 

to VIDEO/Y jack or connect

 

 

 

 

 

This projector uses a micro processor

 

 

Connect S-VIDEO output

component video outputs to

 

 

VIDEO/Y, Cb/Pb and Cr/Pr

to control this unit, and occasionally,

 

 

from video equipment to this

jacks. (Refer to P14.)

this micro processor may malfunction

 

 

jack. (Refer to P14.)

 

and need to be reset. This can be

 

 

 

 

done by pressing RESET button with a

 

AUDIO INPUT JACKS

 

pen, which will shut down and restart

 

(INPUT 3 and INPUT 4)

 

unit. Do not use RESET function

 

 

 

excessively.

Connect an audio output

from video equipment to

 

 

these jacks.

 

(Refer to P14.)

EXTERNAL SPEAKER TERMINALS

Connect External Speaker to these terminals.

(Refer to P13 and P14.)

12

Image 12
Contents Model LC-X50 Multimedia ProjectorTo the Owner Safety Instructions Voor de klanten in NederlandCompliances Esperanza Rancho Santa Margarita CATable of Contents Features and Design Compact Design Digital Zoom for ComputerPreparation Name of Each Part of ProjectorHOT AIR Exhausted SETTING-UP Projector Connecting AC Power CordFor U.S.A. and Canada For Continental Europe Preparation Positioning Projector Room LightPreparation Adjustable Feet Installing Projector in Proper PositionPreparation Moving Projector Connecting Projector Terminals of ProjectorComputer Audio Input 2/ Audio Monitor Output Jack Computer Input 2/MONITOR OutputConnecting to Computer Rear Terminals ProjectorExternal Speaker Terminals Front of the projector External Audio EquipmentConnecting to Video Equipment Rear TerminalsVideo Operation of Remote Control Inside the Battery Compartment BOXBefore Operation Laser Pointer FunctionPoint Volume + Buttons Timer ButtonZoom Button Select ButtonTOP Controls and Indicators Point Volume + / ButtonsHOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Press Menu Button while connecting to PC input source Used to adjust picture imageBefore Operation Menu BAR Used to selectBasic Operation Turning on / OFF ProjectorTurning on Projector Turning OFF ProjectorAdjusting Screen Keystone AdjustmentFocus adjustment may not function properly if the image is Corrected by Keystone adjustmentSound Adjustment Computer Input Selecting Input SourceSelecting Computer System RGBAutomatic MULTI-SCAN System RGBAnalogMonitor out AutoPC Adjustment Auto PC AdjustmentPC Adjust Menu Auto PC AdjComputer Input Manual PC Adjustment Display area Display area HFull screen Picture Image Select Image Level Select DirectImage Level Select Menu Image 1~4Picture Screen Adjustment Screen MenuVideo Input VideoPb/Cb,Pr/Cr Component Video Signal Format Selecting Video SystemPAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-N AV System Menu Video or S-VIDEOPicture level adjusted for picture with fine tone CinemaProvides image at a normal video aspect ratio of 4 Provides image at a wide screen ratio of 16Picture Image Adjustments Image Adjust MenuPicture Image List Mode Picture ImageColor temp White balance RedWhite balance Green White balance BlueSetting Setting MenuSetting Menu Anamorphic Blue backDisplay Menu positionTo change the code of the Remote Control Unit Power managementRemote control To change the code of ProjectorWireless Mouse mode Projector modeUSB Operating Wireless Mouse InstallationOperating Wireless Mouse AppendixMaintenance Section AIR Filter Care and Cleaning on nextIndicatorIndicator Projector so that Ventilation Slots are not obstructedAppendix AIR Filter Care and Cleaning Cleaning Projection LensRecommendation Pull up and removeLamp Replacement Lamp ReplaceMessage Lamp replace counter reset? is displayed. Move Reset Lamp Replace CounterAppendix Lamp Replace Counter Pointer to Yes and then press Select buttonTroubleshooting Remote Control Unit Wireless MouseDoes not work Function does notAppendix Indicators and Projector Condition Appendix Compatible Computer Specifications ResolutionMenu Tree Video sourceSystem Setting Sound Technical Specifications Appendix Configurations of Terminals Control Port ConnectorUSB Connector Series B Computer INPUT-1 and Computer INPUT-2 Terminals AnalogLens Replacement Appendix Optional PartsAppendix Key to better communications Canada
Related manuals
Manual 1 pages 34.06 Kb

LC-X50 specifications

The Eiki LC-X50 is a high-performance LCD projector designed to cater to the needs of professionals and educators, offering a perfect blend of advanced technology and user-friendly features. With its compact lightweight design, the LC-X50 is highly portable, making it an excellent choice for a variety of settings, from business meetings to classrooms.

One of the standout features of the Eiki LC-X50 is its impressive brightness, boasting a luminance of up to 5000 lumens. This makes it suitable for use in environments with significant ambient light, ensuring that presentations remain clear and vibrant. Coupled with a high contrast ratio, the projector delivers exceptional image quality, rendering sharp text and vivid colors that enhance any visual content.

The LC-X50 supports native XGA resolution, with a pixel count of 1024x768, ensuring that both graphics and text look crisp and defined. This native support is complemented by its ability to handle various input resolutions, making it compatible with multiple devices. The projector also features advanced image processing technologies that help to enhance the quality of the projected image, reducing motion blur and improving overall clarity.

Connectivity options on the LC-X50 are extensive, featuring HDMI, VGA, and composite inputs, enabling easy connection to laptops, Blu-ray players, and other multimedia devices. Additionally, the projector includes USB and RS-232 ports, providing flexibility for remote control and integration into a larger AV system.

One of the user-focused designs of the Eiki LC-X50 is its easy-to-navigate menu system, allowing for quick adjustments and setup. The inclusion of a 10W speaker provides sound reinforcement for presentations, eliminating the need for external audio equipment in many situations. With its built-in vertical and horizontal keystone correction feature, users can easily adjust the image for optimal viewing angles, making setup quick and efficient.

Energy efficiency is also a key characteristic of the LC-X50. With a long lamp life, this projector reduces the frequency of lamp replacements, which not only saves on costs but also contributes to lower overall energy consumption.

In summary, the Eiki LC-X50 excels in delivering bright, high-quality images with versatile connectivity and user-friendly operation. Whether for corporate presentations or educational purposes, this projector is a reliable choice, designed to meet the demands of various professional environments while ensuring a remarkable viewing experience.