Eiki LC-X50 instruction manual Picture Image Adjustments, Image Adjust Menu

Page 34

PICTURE IMAGE

PICTURE IMAGE ADJUSTMENTS

1

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT buttons to move a red frame pointer to

 

IMAGE ADJUST Menu icon.

2

Press POINT UP/DOWN button to move a red frame pointer to

item that you want to adjust and then press SELECT button.

Level of each item is displayed. Adjust each level by pressing POINT LEFT/RIGHT button(s).

Contrast

Press POINT LEFT button to decrease contrast, and POINT RIGHT button to increase contrast. (From 0 to 63.)

Brightness

Press POINT LEFT button to adjust image darker, and POINT RIGHT button to adjust brighter. (From 0 to 63.)

Color

Press POINT LEFT button to lighten color, and POINT RIGHT button to deeper color. (From 0 to 63.)

Tint

Press POINT LEFT button or POINT RIGHT button to obtain proper color. (From 0 to 63.)

Color Management

The Color management function can be used to adjust the level, phase and gamma of the selected display colors on the screen, and to replace these colors with other colors if required.

The projector lets you replace up to eight colors for each image. There are four preset images for VIDEO mode and four preset images for PC, giving a total of eight images.

1

Press the POINT UP/DOWN button to move the red frame point-

er to "COLOR MANAGEMENT", and then press the SELECT

 

button. The COLOR MANAGEMENT menu will appear and

 

pointer mode will be enabled. The image that was being project-

 

ed when the button was pressed will be paused, and the COLOR

 

MANAGEMENT POINTER will appear.

2

Use the POINT buttons to move the pointer to a section of the

paused image that contains the color that you would like to

 

adjust, and then press the SELECT button. The mode will

 

change to COLOR SELECTION mode, and the color in the cen-

 

ter of the pointer will be selected and adjustment will be possi-

 

ble.

3

Use the POINT buttons to adjust the level and phase of the

color, and then press the SELECT button to confirm the setting.

Next, use the POINT buttons to adjust the gamma correction for the color, and then press the SELECT button to accept the set- ting. When the SELECT button is pressed, the mode will change to LIST mode.

IMAGE ADJUST MENU

IMAGE ADJUST

Menu icon

Move a red frame pointer to item to be selected and then press SELECT button.

Press POINT LEFT/RIGHT buttons to adjust value.

POINTER MODE

COLOR

MANAGEMENT

POINTER

NOTE;

Press the COLOR M. button on the remote con- trol to display the COLOR MANAGEMENT menu. If you would like to check or re-adjust a color management setting that has already been made, press the COLOR M. button on the remote control once more to change to LIST mode.

34

Image 34
Contents Model LC-X50 Multimedia ProjectorTo the Owner Safety Instructions Voor de klanten in NederlandCompliances Esperanza Rancho Santa Margarita CATable of Contents Features and Design Compact Design Digital Zoom for ComputerName of Each Part of Projector PreparationHOT AIR Exhausted Connecting AC Power Cord SETTING-UP ProjectorFor U.S.A. and Canada For Continental Europe Preparation Positioning Projector Room LightPreparation Adjustable Feet Installing Projector in Proper PositionPreparation Moving Projector Computer Audio Input 2/ Audio Monitor Output Jack Connecting ProjectorTerminals of Projector Computer Input 2/MONITOR OutputExternal Speaker Terminals Front of the projector Connecting to ComputerRear Terminals Projector External Audio EquipmentRear Terminals Connecting to Video EquipmentVideo Before Operation Operation of Remote ControlInside the Battery Compartment BOX Laser Pointer FunctionZoom Button Point Volume + ButtonsTimer Button Select ButtonTOP Controls and Indicators Point Volume + / ButtonsOperating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Press Menu Button while connecting to PC input sourceUsed to adjust picture image Used to selectTurning on Projector Basic OperationTurning on / OFF Projector Turning OFF ProjectorFocus adjustment may not function properly if the image is Adjusting ScreenKeystone Adjustment Corrected by Keystone adjustmentSound Adjustment Selecting Computer System Computer InputSelecting Input Source RGBMonitor out Automatic MULTI-SCAN SystemRGBAnalog AutoPC Adjust Menu PC AdjustmentAuto PC Adjustment Auto PC AdjComputer Input Manual PC Adjustment Display area H Display areaFull screen Image Level Select Menu Picture Image SelectImage Level Select Direct Image 1~4Picture Screen Adjustment Screen MenuVideo Video InputPb/Cb,Pr/Cr PAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-N Component Video Signal FormatSelecting Video System AV System Menu Video or S-VIDEOPicture level adjusted for picture with fine tone CinemaProvides image at a normal video aspect ratio of 4 Provides image at a wide screen ratio of 16Image Adjust Menu Picture Image AdjustmentsPicture Image List Mode Picture ImageWhite balance Green Color tempWhite balance Red White balance BlueSetting Menu SettingSetting Menu Display AnamorphicBlue back Menu positionRemote control To change the code of the Remote Control UnitPower management To change the code of ProjectorProjector mode Wireless Mouse modeUSB Operating Wireless Mouse Operating Wireless MouseInstallation AppendixIndicatorIndicator MaintenanceSection AIR Filter Care and Cleaning on next Projector so that Ventilation Slots are not obstructedRecommendation Appendix AIR Filter Care and CleaningCleaning Projection Lens Pull up and removeLamp Replacement Lamp ReplaceAppendix Lamp Replace Counter Message Lamp replace counter reset? is displayed. MoveReset Lamp Replace Counter Pointer to Yes and then press Select buttonTroubleshooting Does not work Remote Control UnitWireless Mouse Function does notAppendix Indicators and Projector Condition Appendix Compatible Computer Specifications ResolutionMenu Tree Video sourceSystem Setting Sound Technical Specifications USB Connector Series B Appendix Configurations of TerminalsControl Port Connector Computer INPUT-1 and Computer INPUT-2 Terminals AnalogLens Replacement Appendix Optional PartsAppendix Key to better communications Canada
Related manuals
Manual 1 pages 34.06 Kb

LC-X50 specifications

The Eiki LC-X50 is a high-performance LCD projector designed to cater to the needs of professionals and educators, offering a perfect blend of advanced technology and user-friendly features. With its compact lightweight design, the LC-X50 is highly portable, making it an excellent choice for a variety of settings, from business meetings to classrooms.

One of the standout features of the Eiki LC-X50 is its impressive brightness, boasting a luminance of up to 5000 lumens. This makes it suitable for use in environments with significant ambient light, ensuring that presentations remain clear and vibrant. Coupled with a high contrast ratio, the projector delivers exceptional image quality, rendering sharp text and vivid colors that enhance any visual content.

The LC-X50 supports native XGA resolution, with a pixel count of 1024x768, ensuring that both graphics and text look crisp and defined. This native support is complemented by its ability to handle various input resolutions, making it compatible with multiple devices. The projector also features advanced image processing technologies that help to enhance the quality of the projected image, reducing motion blur and improving overall clarity.

Connectivity options on the LC-X50 are extensive, featuring HDMI, VGA, and composite inputs, enabling easy connection to laptops, Blu-ray players, and other multimedia devices. Additionally, the projector includes USB and RS-232 ports, providing flexibility for remote control and integration into a larger AV system.

One of the user-focused designs of the Eiki LC-X50 is its easy-to-navigate menu system, allowing for quick adjustments and setup. The inclusion of a 10W speaker provides sound reinforcement for presentations, eliminating the need for external audio equipment in many situations. With its built-in vertical and horizontal keystone correction feature, users can easily adjust the image for optimal viewing angles, making setup quick and efficient.

Energy efficiency is also a key characteristic of the LC-X50. With a long lamp life, this projector reduces the frequency of lamp replacements, which not only saves on costs but also contributes to lower overall energy consumption.

In summary, the Eiki LC-X50 excels in delivering bright, high-quality images with versatile connectivity and user-friendly operation. Whether for corporate presentations or educational purposes, this projector is a reliable choice, designed to meet the demands of various professional environments while ensuring a remarkable viewing experience.