Eiki LC-X50 Appendix Lamp Replace Counter, Message Lamp replace counter reset? is displayed. Move

Page 45

APPENDIX

LAMP REPLACE COUNTER

Be sure to reset the Lamp Replace Counter after the Lamp Assembly is replaced. When the Lamp Replace Counter is reset, the LAMP REPLACE Indicator stops lighting.

1

Turn projector on, press MENU button and ON-SCREEN

 

MENU will appear. Press POINT LEFT/RIGHT button(s) to

 

move a red frame pointer to SETTING Menu icon (refer to

 

page 40).

2

Press POINT UP/DOWN button to move a red frame pointer

 

to “Lamp counter reset” and then press SELECT button. The

 

message "Lamp replace counter reset?" is displayed. Move

 

the pointer to [Yes] and then press SELECT button.

3

Another confirmation dialog box appears and select [Yes] to

reset Lamp Replace Counter.

Move the pointer to Lamp counter reset and then press SELECT button. The message “Lamp replace counter reset?” is displayed.

NOTE : Do not reset the Lamp Replace Counter until after the Projection Lamp is replaced.

LAMP HANDLING PRECAUTIONS

This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may result in accidents, injury, or create a fire hazard.

Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than other similar lamps.

If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE INDICATOR lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.

( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual. ) Continuous use of the lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion.

A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.

IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.

If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken glass.

45

Image 45
Contents Multimedia Projector Model LC-X50To the Owner Voor de klanten in Nederland Safety InstructionsEsperanza Rancho Santa Margarita CA CompliancesTable of Contents Compact Design Digital Zoom for Computer Features and DesignPreparation Name of Each Part of ProjectorHOT AIR Exhausted SETTING-UP Projector Connecting AC Power CordFor U.S.A. and Canada For Continental Europe Room Light Preparation Positioning ProjectorInstalling Projector in Proper Position Preparation Adjustable FeetPreparation Moving Projector Terminals of Projector Connecting ProjectorComputer Audio Input 2/ Audio Monitor Output Jack Computer Input 2/MONITOR OutputRear Terminals Projector Connecting to ComputerExternal Speaker Terminals Front of the projector External Audio EquipmentConnecting to Video Equipment Rear TerminalsVideo Inside the Battery Compartment BOX Operation of Remote ControlBefore Operation Laser Pointer FunctionTimer Button Point Volume + ButtonsZoom Button Select ButtonPoint Volume + / Buttons TOP Controls and IndicatorsHOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Used to adjust picture image Press Menu Button while connecting to PC input sourceBefore Operation Menu BAR Used to selectTurning on / OFF Projector Basic OperationTurning on Projector Turning OFF ProjectorKeystone Adjustment Adjusting ScreenFocus adjustment may not function properly if the image is Corrected by Keystone adjustmentSound Adjustment Selecting Input Source Computer InputSelecting Computer System RGBRGBAnalog Automatic MULTI-SCAN SystemMonitor out AutoAuto PC Adjustment PC AdjustmentPC Adjust Menu Auto PC AdjComputer Input Manual PC Adjustment Display area Display area HFull screen Image Level Select Direct Picture Image SelectImage Level Select Menu Image 1~4Screen Menu Picture Screen AdjustmentVideo Input VideoPb/Cb,Pr/Cr Selecting Video System Component Video Signal FormatPAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-N AV System Menu Video or S-VIDEOCinema Picture level adjusted for picture with fine toneProvides image at a wide screen ratio of 16 Provides image at a normal video aspect ratio of 4Picture Image Adjustments Image Adjust MenuPicture Image Picture Image List ModeWhite balance Red Color tempWhite balance Green White balance BlueSetting Setting MenuSetting Menu Blue back AnamorphicDisplay Menu positionPower management To change the code of the Remote Control UnitRemote control To change the code of ProjectorWireless Mouse mode Projector modeUSB Installation Operating Wireless MouseOperating Wireless Mouse AppendixSection AIR Filter Care and Cleaning on next MaintenanceIndicatorIndicator Projector so that Ventilation Slots are not obstructedCleaning Projection Lens Appendix AIR Filter Care and CleaningRecommendation Pull up and removeLamp Replace Lamp ReplacementReset Lamp Replace Counter Message Lamp replace counter reset? is displayed. MoveAppendix Lamp Replace Counter Pointer to Yes and then press Select buttonTroubleshooting Wireless Mouse Remote Control UnitDoes not work Function does notAppendix Indicators and Projector Condition Resolution Appendix Compatible Computer SpecificationsVideo source Menu TreeSystem Setting Sound Technical Specifications Control Port Connector Appendix Configurations of TerminalsUSB Connector Series B Computer INPUT-1 and Computer INPUT-2 Terminals AnalogAppendix Optional Parts Lens ReplacementAppendix Key to better communications Canada
Related manuals
Manual 1 pages 34.06 Kb

LC-X50 specifications

The Eiki LC-X50 is a high-performance LCD projector designed to cater to the needs of professionals and educators, offering a perfect blend of advanced technology and user-friendly features. With its compact lightweight design, the LC-X50 is highly portable, making it an excellent choice for a variety of settings, from business meetings to classrooms.

One of the standout features of the Eiki LC-X50 is its impressive brightness, boasting a luminance of up to 5000 lumens. This makes it suitable for use in environments with significant ambient light, ensuring that presentations remain clear and vibrant. Coupled with a high contrast ratio, the projector delivers exceptional image quality, rendering sharp text and vivid colors that enhance any visual content.

The LC-X50 supports native XGA resolution, with a pixel count of 1024x768, ensuring that both graphics and text look crisp and defined. This native support is complemented by its ability to handle various input resolutions, making it compatible with multiple devices. The projector also features advanced image processing technologies that help to enhance the quality of the projected image, reducing motion blur and improving overall clarity.

Connectivity options on the LC-X50 are extensive, featuring HDMI, VGA, and composite inputs, enabling easy connection to laptops, Blu-ray players, and other multimedia devices. Additionally, the projector includes USB and RS-232 ports, providing flexibility for remote control and integration into a larger AV system.

One of the user-focused designs of the Eiki LC-X50 is its easy-to-navigate menu system, allowing for quick adjustments and setup. The inclusion of a 10W speaker provides sound reinforcement for presentations, eliminating the need for external audio equipment in many situations. With its built-in vertical and horizontal keystone correction feature, users can easily adjust the image for optimal viewing angles, making setup quick and efficient.

Energy efficiency is also a key characteristic of the LC-X50. With a long lamp life, this projector reduces the frequency of lamp replacements, which not only saves on costs but also contributes to lower overall energy consumption.

In summary, the Eiki LC-X50 excels in delivering bright, high-quality images with versatile connectivity and user-friendly operation. Whether for corporate presentations or educational purposes, this projector is a reliable choice, designed to meet the demands of various professional environments while ensuring a remarkable viewing experience.