Eiki LC-X50 Before Operation, Operation of Remote Control, Laser Pointer Function

Page 15

BEFORE OPERATION

OPERATION OF REMOTE CONTROL

Left Side

ON

ALL OFF

ALL-OFF SWITCH

When using Remote Control Unit, turn this switch to “ON.” And turn it to “ALL OFF” when it is not used.

INSIDE THE BATTERY COMPARTMENT BOX

This remote control provide the DIP switches into the battery compartment box.

Slide the SW4 (LASER ON/OFF switch) to "OFF" position. The laser pointer function is not operated.

Set switches 1-3 as shown in table below depending on Code No. that you want to select remote control code.

(Refer to P39.)

DIP SWITCH SETTING

 

 

 

 

 

 

 

SW4 ........ LASER ON/OFF

 

 

 

 

 

 

 

SW1

SW2

SW3

Code No.

 

 

 

 

4

 

ON

ON

ON

Code 1

 

 

 

 

 

 

 

ON

 

 

 

3

 

ON

ON

OFF

Code 2

 

 

 

2

 

ON

OFF

ON

Code 3

 

 

 

 

 

 

 

ON

OFF

OFF

Code 4

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

OFF

ON

ON

Code 5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF

ON

OFF

Code 6

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF

OFF

ON

Code 7

 

 

 

 

 

 

 

OFF

OFF

OFF

Code 8

LASER POINTER (Drag ON)

INDICATOR

Lights red while laser beam is emitted from Laser Light Window.

Lights green when drag ON position. (P41)

MUTE BUTTON

Used to mute sound. (P22)

DRAG ON/OFF BUTTON

Used to select drag ON/OFF position. (P41)

LEFT CLICK BUTTON

Used as a PC mouse in Wireless Mouse Operation. Press this button and the mouse pointer button to drag

aselected screen object. (P41)

LASER BUTTON

Used to operate Laser Pointer Function. Laser beam is emitted while pressing this button within 1 minute.

When using this Laser Pointer for more than 1 minute, release LASER button and press it again.

FOCUS BUTTON

Used to adjust focus. (P21)

LOCK

AUTO PC ON-OFF

D.ZOOM FREEZE NO SHOW

MUTE IMAGE

VOLUME- SELECT VOLUME+

MENU KEYSTONE

LASER

P-TIMER

INPUT 1

ZOOM COLOR.M

INPUT 2

 

INPUT 3

FOCUS LENS

INPUT 4

POWER ON-OFF BUTTON

Used to turn projector on or off. (P20)

AUTO PC ADJ. BUTTON

Use to operate AUTO PC Adjustment function. (P25)

IMAGE BUTTON

Used to select image level. (P28, 32)

KEYSTONE BUTTON

Used to correct keystone distortion. (P21, 37)

MOUSE POINTER

Used as a PC mouse in Wireless Mouse Operation. (P41)

RIGHT CLICK BUTTON

Used as a PC mouse in Wireless Mouse Operation. (P41)

LENS SHIFT BUTTON

Used to select LENS SHIFT function. (P21)

WIRED REMOTE JACK

When using as Wired Remote Control, connect Remote Control Cable to this jack.

Battery installation is required when using as Wired Remote Control.

LASER POINTER FUNCTION

This Remote Control Unit emits a laser beam as laser pointer function from Laser Light Window. When LASER button is pressed, laser light goes on. And when LASER button is being pressed for more than 1 minute or LASER button is released, light goes off. LASER POINTER INDICATOR lights RED and Laser is emitted with RED light to indicate laser beam is being emitted.

Laser emitted is a class II laser; therefore, do not look into Laser Light Window or shine laser beam on yourself or other people. Three marks below are caution labels for laser beam.

CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result hazardous radiation exposure.

These caution labels are put on remote control.

LASER POINTER INDICATOR

Laser Light Window

15

Image 15
Contents Multimedia Projector Model LC-X50To the Owner Voor de klanten in Nederland Safety InstructionsEsperanza Rancho Santa Margarita CA CompliancesTable of Contents Compact Design Digital Zoom for Computer Features and DesignPreparation Name of Each Part of ProjectorHOT AIR Exhausted SETTING-UP Projector Connecting AC Power CordFor U.S.A. and Canada For Continental Europe Room Light Preparation Positioning ProjectorInstalling Projector in Proper Position Preparation Adjustable FeetPreparation Moving Projector Computer Input 2/MONITOR Output Connecting ProjectorTerminals of Projector Computer Audio Input 2/ Audio Monitor Output JackExternal Audio Equipment Connecting to ComputerRear Terminals Projector External Speaker Terminals Front of the projectorConnecting to Video Equipment Rear TerminalsVideo Laser Pointer Function Operation of Remote ControlInside the Battery Compartment BOX Before OperationSelect Button Point Volume + ButtonsTimer Button Zoom ButtonPoint Volume + / Buttons TOP Controls and IndicatorsHOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Used to select Press Menu Button while connecting to PC input sourceUsed to adjust picture image Before Operation Menu BARTurning OFF Projector Basic OperationTurning on / OFF Projector Turning on ProjectorCorrected by Keystone adjustment Adjusting ScreenKeystone Adjustment Focus adjustment may not function properly if the image isSound Adjustment RGB Computer InputSelecting Input Source Selecting Computer SystemAuto Automatic MULTI-SCAN SystemRGBAnalog Monitor outAuto PC Adj PC AdjustmentAuto PC Adjustment PC Adjust MenuComputer Input Manual PC Adjustment Display area Display area HFull screen Image 1~4 Picture Image SelectImage Level Select Direct Image Level Select MenuScreen Menu Picture Screen AdjustmentVideo Input VideoPb/Cb,Pr/Cr AV System Menu Video or S-VIDEO Component Video Signal FormatSelecting Video System PAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-NCinema Picture level adjusted for picture with fine toneProvides image at a wide screen ratio of 16 Provides image at a normal video aspect ratio of 4Picture Image Adjustments Image Adjust MenuPicture Image Picture Image List ModeWhite balance Blue Color tempWhite balance Red White balance GreenSetting Setting MenuSetting Menu Menu position AnamorphicBlue back DisplayTo change the code of Projector To change the code of the Remote Control UnitPower management Remote controlWireless Mouse mode Projector modeUSB Appendix Operating Wireless MouseInstallation Operating Wireless MouseProjector so that Ventilation Slots are not obstructed MaintenanceSection AIR Filter Care and Cleaning on next IndicatorIndicatorPull up and remove Appendix AIR Filter Care and CleaningCleaning Projection Lens RecommendationLamp Replace Lamp ReplacementPointer to Yes and then press Select button Message Lamp replace counter reset? is displayed. MoveReset Lamp Replace Counter Appendix Lamp Replace CounterTroubleshooting Function does not Remote Control UnitWireless Mouse Does not workAppendix Indicators and Projector Condition Resolution Appendix Compatible Computer SpecificationsVideo source Menu TreeSystem Setting Sound Technical Specifications Computer INPUT-1 and Computer INPUT-2 Terminals Analog Appendix Configurations of TerminalsControl Port Connector USB Connector Series BAppendix Optional Parts Lens ReplacementAppendix Key to better communications Canada
Related manuals
Manual 1 pages 34.06 Kb

LC-X50 specifications

The Eiki LC-X50 is a high-performance LCD projector designed to cater to the needs of professionals and educators, offering a perfect blend of advanced technology and user-friendly features. With its compact lightweight design, the LC-X50 is highly portable, making it an excellent choice for a variety of settings, from business meetings to classrooms.

One of the standout features of the Eiki LC-X50 is its impressive brightness, boasting a luminance of up to 5000 lumens. This makes it suitable for use in environments with significant ambient light, ensuring that presentations remain clear and vibrant. Coupled with a high contrast ratio, the projector delivers exceptional image quality, rendering sharp text and vivid colors that enhance any visual content.

The LC-X50 supports native XGA resolution, with a pixel count of 1024x768, ensuring that both graphics and text look crisp and defined. This native support is complemented by its ability to handle various input resolutions, making it compatible with multiple devices. The projector also features advanced image processing technologies that help to enhance the quality of the projected image, reducing motion blur and improving overall clarity.

Connectivity options on the LC-X50 are extensive, featuring HDMI, VGA, and composite inputs, enabling easy connection to laptops, Blu-ray players, and other multimedia devices. Additionally, the projector includes USB and RS-232 ports, providing flexibility for remote control and integration into a larger AV system.

One of the user-focused designs of the Eiki LC-X50 is its easy-to-navigate menu system, allowing for quick adjustments and setup. The inclusion of a 10W speaker provides sound reinforcement for presentations, eliminating the need for external audio equipment in many situations. With its built-in vertical and horizontal keystone correction feature, users can easily adjust the image for optimal viewing angles, making setup quick and efficient.

Energy efficiency is also a key characteristic of the LC-X50. With a long lamp life, this projector reduces the frequency of lamp replacements, which not only saves on costs but also contributes to lower overall energy consumption.

In summary, the Eiki LC-X50 excels in delivering bright, high-quality images with versatile connectivity and user-friendly operation. Whether for corporate presentations or educational purposes, this projector is a reliable choice, designed to meet the demands of various professional environments while ensuring a remarkable viewing experience.