Weider Pro 2250 Cable Assembly, Trap is turned to hold the Cable in the groove of the Pulley

Page 8

8.Identify the Right Arm (48) and the Left Arm (47) by the position of the welded bracket on each Arm.

Press a 2” Round Inner Cap (33) into the lower end of the Left Arm (47). Wet the end of the Arm with soapy water and slide a 10” Pad (45) onto it. Make sure the 1 1/8” x 2 1/2” Plastic Bushing (74) is in the Arm.

Lubricate both axles on the Top Frame (55). Have another person slide the Left Arm (47) onto the left axle on the Top Frame. Note: Be careful not to confuse the Right Arm (48) with the Left Arm. Make sure that the upper end of the Left Arm is behind the indicated bracket on the Top Frame.

Set two 1” Retainers (69) on top of a 1” Round Cover Cap (70). Make sure that the teeth on the

Retainers bend toward the Cover Cap, as shown in the inset drawing. Tap the Retainers and Cap onto the Left axle on the Top Frame (55).

Attach the Right Arm (48) in the same manner.

Cable Assembly

9.During steps 9 through 20, see the CABLE DIAGRAMS on page 17 of this manual to verify proper cable routing.

Locate the Short Cable (58). Lay the Cable in the bracket on the Base (4) and under the Press Frame (17). Attach a 3 1/2” Pulley (15) to the bracket with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). Make sure that the end of the

Cable with the ball is on the indicated side of the bracket.

10.Route the Short Cable (58) under a 3 1/2” Pulley (15) Attach the Pulley and a Cable Trap (66) to

the lower hole in the Front Upright (42) with a 3/8” x 3 3/4” Bolt (71), a 3/8” Washer (9), and a 3/8” Nylon Locknut (21). Make sure that the Cable

Trap is turned to hold the Cable in the groove of the Pulley.

8

8

 

 

 

55

 

 

 

48

 

 

 

Bracket

 

 

Lubricate

74

 

Axle

 

 

 

 

69

 

 

 

70

47

 

 

55

 

 

 

69

33

 

 

45

 

 

 

70

 

 

 

9

 

 

 

17

 

 

 

15

 

 

 

21

 

 

 

58

 

 

 

 

12

 

 

 

4

 

 

Bracket

 

 

10

 

 

 

 

42

 

 

21

9

 

 

 

15

66

71

 

 

 

 

58

 

 

Image 8
Contents Model No Serial No Sears, Roebuck and Co., Hoffman Estates, ILTable of Contents Important Precautions DecalBefore YOU Begin For your benefit, read this manual carefully beforeRight Side Left SideAssembly Frame AssemblyMake Things Easier for Yourself Stabilizer Foot in the same mannerTighten the 5/16 Nylon Locknuts 3 used in step Assemble the other Press Arm 73 in the same manner Arm AssemblyTighten the 5/16 Nylon Locknuts 3 used in steps 2 Cable Assembly Trap is turned to hold the Cable in the groove of the PulleyHook Ball Page Seat Assembly Page Attaching the Accessories AdjustmentsChanging the Weight Setting Attaching and Removing the Seat Attaching the LEG Lever to the LOW Pulley StationWeight Resistance Chart Troubleshooting Tightening the CablesCable Diagrams Long Cable Short CableExercise Guidelines Staying Motivated Muscle ChartCooling Down Part LIST-Model No Key No. Qty DescriptionExploded DRAWING-Model No Part Identification CHART-Model No .159300 R0903A Page Full 90-DAY Warranty Sears, Roebuck and Co., Dept 817WA, Hoffman Estates, IL