Weider WEBE15210 Uprights 4. Note Make sure the decal on, Tighten the Nylon Locknuts yet

Page 7

2. Position the Crossbar (3) between the two

2

 

 

 

 

 

Uprights (4). Note: Make sure the decal on the

 

Decal

 

 

Holes

 

 

 

35

Crossbar is in the position shown. Attach the

 

 

 

 

 

 

 

21

 

 

 

Crossbar to each Upright with four M10 x 95mm

 

 

 

 

4

 

 

 

 

 

Bolts (34), two Support Plates (21), and four M10

 

3

 

 

 

 

Nylon Locknuts (35). Do not tighten the Nylon

 

 

 

 

 

 

 

 

 

 

 

Locknuts yet.

 

 

 

 

 

35

 

 

 

 

 

 

 

 

34

 

 

 

 

 

 

21

 

 

 

 

 

 

34

 

 

 

3. Attach the Frame (1) to the Crossbar (3) with two

3

 

 

 

 

 

M10 x 95mm Bolts (34) and two M10 Nylon

 

 

 

 

35

 

 

 

 

 

Locknuts (35). Do not tighten the Nylon

 

 

 

 

 

 

Locknuts yet.

 

 

 

 

 

 

Press two 8mm Bushings (32) into the indicated

 

 

34

 

 

3

locations on the Frame (1).

 

32

 

 

20

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press a 75mm x 50mm Inner Cap (20) into the

 

 

 

 

 

 

Frame (1).

 

 

1

 

 

 

 

 

 

 

 

 

 

 

32

 

 

 

 

4. Press two 50mm Square Inner Caps (22) into the

4

 

 

 

 

 

Front Stabilizer (2).

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

35

Attach the Front Stabilizer (2) to the Frame (1)

 

 

 

 

 

 

2

 

 

 

 

with two M10 x 65mm Bolts (36), two M10

 

 

 

 

 

 

 

 

 

 

 

Washers (27), and two M10 Nylon Locknuts (35).

 

 

 

 

 

 

Tighten the M10 Nylon Locknuts (34) used in

22

 

 

 

 

 

 

 

 

 

 

steps 1-4.

 

36

27

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

22

 

 

 

5. Press four 20mm x 40mm Inner Caps (43) into

5

 

 

 

 

 

the Backrest Frames (10). Orient the Backrest

 

 

 

 

 

 

 

8

 

 

 

Frames as shown. Note: The indents in the

 

 

 

 

 

 

 

 

 

 

 

Backrest Frames must be on top.

 

 

 

 

 

 

Attach the Backrest Bracket (9) to the Backrest

 

 

 

40

 

 

Frames (10) with four M8 x 55mm Carriage Bolts

 

 

 

 

43

 

 

 

 

 

(40) and four M8 Nylon Locknuts (42). Do not

 

Indent

 

 

 

 

tighten the Nylon Locknuts yet.

 

10

 

 

 

19

 

 

 

 

 

Attach the Backrest (8) to the Backrest Frames

 

 

 

 

 

 

(10) with four M6 x 50mm Bolts (39) and four M6

 

 

 

 

 

 

Washers (19). Do not tighten the Bolts yet.The

 

43 19

 

 

39

 

Backrest must be oriented as shown.

 

 

 

 

 

 

 

39

 

 

42

 

 

 

 

 

 

 

 

 

9

42

 

 

 

 

 

 

 

 

 

 

7

 

 

 

 

 

Image 7
Contents Model No. WEBE15210 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Before YOU Begin Part Identification Chart Make Things Easier for Yourself AssemblyDo not tighten the M10 Nylon Locknuts 35 yet Locknuts 35. Do not tighten the Nylon Locknuts yet Uprights 4. Note Make sure the decal onCrossbar is in the position shown. Attach Nylon Locknuts 35. Do not tighten the Nylon Locknuts yetAble to pivot easily Ing decals on the Plastic Plates must faceAway from the bench. Do not overtighten M10 Nylon Locknut the Backrest 8 must beAdjustment Hole Knobs 18 are fully tightened AdjustmentsAdjusting the Backrest Adjusting the Weight Rest and Weight SpotterExercise Guidelines Cooling Down Muscle ChartStaying Motivated Thursday Aerobic Exercise Date Exercise Weight Sets RepsDate Aerobic ExerciseQty Description Part LIST-Model No. WEBE15210R1001A Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT