6. Press four 25mm Square Inner Caps (39) into the | 6 |
|
|
|
|
|
ends of the Backrest Tubes (20). Be sure the |
|
|
|
|
| |
|
|
|
|
|
| |
Caps are oriented as shown. |
|
|
|
|
|
|
Attach the Backrest (15) to the Backrest Tubes | 15 |
|
|
|
| Narrow |
(20) using four M6 x 38mm Screws (14) and four |
|
|
|
| 39 | End |
M6 Washers (31). Be sure the narrow end of |
|
|
|
|
|
|
the Backrest is on the end shown. Do not |
|
|
|
| 31 |
|
tighten the Screws yet. |
|
| 14 |
| 31 |
|
|
|
|
|
| ||
|
| 31 | 20 | 14 |
| |
|
|
|
|
| ||
| 14 |
| 31 |
|
|
|
| 39 | 14 |
|
|
|
|
7. Press two 25mm Square Inner Caps (39) into the | 7 |
|
|
|
|
|
Adjustment Tube (37). With the pins on the |
|
|
|
|
| |
| 39 |
|
|
| ||
Adjustment Tube facing downward, slide the |
|
| 37 |
| ||
Adjustment Tube into a set of adjustment brack- |
|
|
|
|
| |
|
|
|
|
|
| |
ets on the Uprights (4, 5). |
|
|
|
|
|
|
Lubricate an M10 x 168mm Bolt (40). Attach the |
|
|
|
|
|
|
Backrest Tubes (20) to the Bench Frame (1) with |
|
|
|
|
| 39 |
the Bolt, two M10 Washers (29), and an M10 |
|
|
|
|
| |
|
|
|
|
|
| |
Nylon Locknut (45). Do not overtighten the |
|
|
|
|
|
|
Nylon Locknut; the Backrest Tubes must be |
|
|
|
|
|
|
able to pivot freely. | 45 |
|
|
|
|
|
|
|
|
|
|
| |
Tighten the M8 Nylon Locknuts (43) used in |
|
|
|
|
|
|
step 2, and the four M6 x 38mm Screws (14) | 29 |
|
| 5 |
|
|
used in step 6. |
|
|
|
| ||
20 |
|
|
|
| ||
| 29 |
|
|
|
| |
|
| 40 |
|
| 4 | |
|
|
|
|
|
| |
| 1 |
|
| Bracket |
| |
|
|
|
|
|
| |
|
|
| Lubricate |
|
|
|
8. Attach the Seat (16) to the Bench Frame (1) | 8 |
|
|
|
|
|
using two M6 x 16mm Screws (10), an M6 x |
|
|
|
|
|
|
50mm Screw (38), and an M6 Washer (31). |
| 16 |
|
|
|
|
|
|
| 1 |
|
|
|
|
|
|
| 31 |
|
|
|
|
| 10 | 38 |
|
|
|
|
|
|
|
| |
7