Weider PRO XT75 user manual Tighten all Nylon Locknuts 31 used in steps

Page 8

6.Attach the Chin-up Bar (13) and two Joint Plates (6) to the Front Uprights (7) using four M10 x 78mm Bolts (33) and four M10 Nylon Locknuts (31). Do not tighten the Nylon Locknuts yet.

7.Press a 60mm Square Inner Cap (29) into the Left Frame (12). Attach the Left Frame to the left Uprights (7, 8) using four M10 x 78mm Bolts (33) and four M10 Nylon Locknuts (31). Do not tighten the Nylon Locknuts yet.

Assemble the Right Frame (10) to the right Uprights (7, 8) in the same manner.

Attach the Center Frame (11) to the Right and Left Frames (10, 12) using four M10 x 78mm Bolts (33) and four M10 Nylon Locknuts (31).

Tighten all Nylon Locknuts (31) used in steps 1–7.

8.Press the two 51mm Round Inner Caps (46) into the weight tubes on the Weight Carriage (15).

Press the two Carriage Bushings (16) into the Weight Carriage (15). Make sure the Weight

Carriage is turned so the weight tubes are near the top, as shown. Attach the lower Carriage Bushing using an M10 x 66mm Bolt (37), two M10 Flat Washers (41), the 51mm Spacer (43), and an M10 Nylon Locknut (31).

9.Set the two Weight Bumpers (18) over the indicated holes in the Weight Guide Base (4). Hold the Weight Carriage (15) on top of the Weight Bumpers.

Insert the two Weight Guides (9) into the Weight Carriage (15), the Weight Bumpers (18), and the Weight Guide Base (4). Attach the Weight Guides using two M8 x 72mm Bolts (35), four M8 Flat Washers (40), and two M8 Nylon Locknuts (32).

8

6

 

6

 

 

 

33

 

13

 

 

 

 

 

 

 

31

 

 

 

 

 

 

6

 

 

7

31

 

 

 

 

 

 

 

 

7

33

 

 

 

 

7

 

 

11

 

 

 

 

 

 

10

 

 

 

 

 

 

 

31

 

 

31

 

29

 

 

33

 

 

 

 

 

 

33

8

12

 

 

 

 

31

 

 

33

 

 

7

 

 

 

 

 

 

 

 

 

33

8

 

 

 

 

 

 

7

31

 

 

 

 

 

8

46

16

 

 

 

 

 

15

 

Weight Tube

31

 

 

 

41

 

 

46

 

 

 

16

43

41

37

 

9

 

 

9

 

 

 

 

 

 

15

 

32

 

18

 

 

 

 

 

 

4

 

 

 

40

 

 

 

35

Image 8
Contents Model No Serial No SEARS, Roebuck and CO., Hoffman ESTATES, ILTable of Contents Important Precautions Using the Weider PRO XT75 weight rack. If you Before YOU BeginFor your benefit, read this manual carefully before Right Side Part Identification Chart Nylon Locknuts yet AssemblyMake Things Easier for Yourself Spotters and both Weight Rests are at the same height Tighten all Nylon Locknuts 31 used in steps Page Page Page Setting UP the Rack for Squat Exercises AdjustmentsUsing the Weight Rests and Weight Spotters Attaching Weights to the Weight Carriage Tightening the CablesExercise Guidelines Staying Motivated Muscle ChartCooling Down Part LIST-Model No Qty DescriptionExploded Ordering Replacement Parts Full 90-DAY WarrantyModel No SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL