Weider WESY39522 Do not tighten the Locknuts yet, Open the parts bag labeled ARM Assembly

Page 10

12.Attach the Top Frame (6) between the Squat Upright

(4) and the Swivel Upright (5) with four 5/16” x 3 3/4” Bolts (92), the two Short Frame Plates (52), and two 5/16” Nylon Locknuts (86) as shown. Do not tighten the Bolts and Locknuts yet.

Attach the four Weight Guides (42) to the Top Frame

(6)with two 3/8” x 6 1/2” Bolts (95) and two 3/8” Nylon Locknuts (87).

13.Press two 2” x 3” Inner Caps (58) into the Top Frame

(6) and the Butterfly Top Frame (7).

Attach the Butterfly Top Frame (7) to the Top Frame

(6)with two 5/16” x 2 3/4” Bolts (85), two 5/16” Washers (90), and two 5/16” Nylon Locknuts (86).

Do not tighten the Locknuts yet.

Attach the Butterfly Top Frame (7) to the Butterfly Upright (3) with two 5/16” x 3 3/4” Bolts (92), two 5/16” Washers (90), and two 5/16” Nylon Locknuts (86).

Tighten all of the 5/16” Nylon Locknuts (86) and 3/8” Nylon Locknuts (87) used in steps 2–13.

ARM ASSEMBLY

14.Open the parts bag labeled “ARM ASSEMBLY.”

Press three 1 1/2” x 2” Inner Caps (21) into the Leg Lever (10).

Lubricate a 3/8” x 2 1/2” Bolt (18) with grease. Turn the Leg Lever (10) so that the welded tab is on the indicated side, and attach the Leg Lever to the Seat Upright (9) with the Bolt and a 3/8” Nylon Locknut

(87).Do not overtighten the Nylon Locknut; the Leg Lever must be able to pivot easily.

15.Press a 2” x 2 1/2” Inner Cap (125) into the Butterfly Frame (47). Attach the tethers on the two “L”-pins w/Tether (60) to the Butterfly Frame with a #8 x 3/4” Screw (98).

Lubricate a 3/8” x 3” Bolt (107) with grease. Attach the Butterfly Frame (47) to the Butterfly Top Frame

(7)with the Bolt and a 3/8” Nylon Locknut (87). Do not overtighten the Nylon Locknut; the Butterfly Frame must be able to pivot easily.

10

12

 

 

 

 

 

 

 

 

 

6

 

92

52

86

 

 

 

 

 

 

 

 

 

87

 

 

 

 

 

86

 

 

5

 

42

 

 

95

 

 

 

87

52

 

 

 

95

 

92

 

 

 

 

 

 

 

 

 

4

13

 

 

92

 

 

 

 

 

 

90

 

 

7

86

 

58

 

 

 

6

 

 

 

 

 

 

 

 

 

 

90

85

58

 

 

 

 

90

 

 

 

 

86

 

 

 

 

 

3

 

14

 

 

87

9

 

 

 

 

 

 

 

 

21

 

 

 

 

 

 

 

 

 

 

Lubricate

 

21

10

Tab

18

 

 

 

 

 

 

 

 

 

 

 

 

 

21

 

15

 

 

7

 

 

 

 

 

 

 

 

 

125

 

 

 

 

87

107—Lubricate

 

 

 

 

 

 

 

 

 

98

 

 

 

60

 

60

 

 

 

 

 

 

 

 

47

 

 

 

Image 10
Contents Model No. WESY39522 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions DecalFor your benefit, read this manual carefully before Using the weight system. If you have additionalBefore YOU Begin DecalAssembly Frame Assembly Locknuts yet Do not tighten the Nylon Locknuts yetPage Assemble the other weight stack in the same way Open the parts bag labeled ARM Assembly Do not tighten the Locknuts yetCable Assembly Repeat this step with the Left Butterfly ArmTrap is turned to hold the Cable in the groove of the Pulley 100 68 78 126 101 102 Trap is turned to hold the Cable in the groove of the Pulley Page Page Page Seat Assembly Locate and open the parts bag labeled Seat AssemblyNylon Locknuts yet Repeat this step with the other end of the Squat ArmTighten all of the 3/8 Nylon Locknuts 87 used in this step Page Converting the Butterfly Arms AdjustmentsChanging the Weight Setting Ing any exerciseAdjusting the Squat ARM, SEAT, or Butterfly Backrest Adjusting the Squat Knee RestStation Weight Resistance ChartLbs Top Troubleshooting Tightening the CablesLat Cable Cable DiagramsButterfly Cable Swivel High Cable Squat Cable Swivel Cable Leg LeverSwivel Low Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Page Part Identification CHART-Model No. WESY39522 R1202AX 7 Bolt Page Remove this Part LIST/EXPLODED Drawing From the Manual Part LIST-Model No. WESY39522 Key Qty DescriptionExploded