Weider WESY85290 Frame Assembly, Chart located in the center of this manual

Page 5

Assembly

Before beginning assembly, carefully read the following information and instructions:

¥Place all parts of the home gym system in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed.

¥The assembly is divided into four stages: 1) frame assembly, 2) press and butterfly arm assembly, 3) cable and pulley assembly, and 4) seat and backrest assembly. The hardware for each stage is packaged separately.

¥Wait until you begin each assembly stage to open that parts bag.

¥For help identifying the small parts used in assembly, use the PART IDENTIFICATION

CHART located in the center of this manual.

Note: Some small parts may have been pre- attached for shipping. If a part is not in the parts bag, check to see if it has been pre-attached.

¥As you assemble the home gym system, be sure that all parts are oriented as shown in the drawings.

¥Tighten all parts as you assemble them, unless instructed to do otherwise.

THE FOLLOWING TOOLS (NOT INCLUDED) ARE REQUIRED FOR ASSEMBLY:

¥Two (2) adjustable wrenches

¥One (1) standard screwdriver

¥One (1) phillips screwdriver

¥One (1) rubber mallet

¥Lubricant, such as grease or petroleum jelly, and soapy water will also be needed.

Assembly will be more convenient if you have the following tools: A socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches.

FRAME ASSEMBLY

1.Before beginning assembly, be sure that you have read and understand the infor- mation in the box above.

Press a 2Ó Square Outer Cap (51) onto each end of the Stabilizer (5). Press a 2Ó Square Inner Cap (27) into the end of the Base (4).

Insert two 5/16Ó x 2 3/4Ó Carriage Bolts (14) up through the Stabilizer (5). Insert four 5/16Ó x 2 1/2Ó Carriage Bolts (1) up through the Base (4).

Slide the indicated end of the Base (4) onto the 5/16Ó x 2 3/4Ó Carriage Bolts (14) in the Stabilizer (5). Slide the Rear Upright (56) onto the Carriage Bolts. Hand tighten a 5/16Ó Nylon Locknut (3) onto each Carriage Bolt.

The high side of the bracket on the Rear Upright must be on the side shown. Do not tighten the Nylon Locknuts yet.

1

 

 

High Side of

 

Bracket

 

56

 

3

 

51

5

 

 

4

51

1

14

 

1

 

27

5

Image 5
Contents Patent Pending Model No. WESY85290 Serial NoCustomer HOT Line Limited Warranty Table of ContentsImportant Precautions Before You Begin DimensionsFrame Assembly AssemblyChart located in the center of this manual Following Tools not Included are Required for AssemblyTighten all Nylon Locknuts used in steps 1 through Nylon Locknuts yetFrame Assembly ARM Assembly Arm with the Left Arm 47 refer to step ARMTighten all Nylon Locknuts used in this Step now Nylon Locknuts until the end of this Assembly stepEnd of the Cable with the ball is on AssemblyIndicated side of the Pulley and that Cable is between the Pulley and the hookCable Assembly Place and that the Cable is routed Cable Trap is turned to hold the CableAround the Pulley as shown Turned to hold the Cable in place and thatCable Assembly Seat Be sure that the Press Adjustment Tube is Oriented as shown Seat Assembly Decal PlacementTROUBLE-SHOOTING and Mainte Nance onChanging the Weight Setting AdjustmentLocking the LEG Lever Weight Resistance ChartTightening the Cables Trouble-shooting and MaintenanceShort Cable Cable DiagramLong Cable Page Page Page Key No. Qty Description Part ListÑModel No. WESY85290Exploded Ordering Replacement Parts