Electrolux EW 1013 I manual Building-in, Preparation and assembly of the door

Page 26

Building-in

This appliance has been designed to be built into the kitchen furniture.

The recess should have the dimensions shown in picture

A.

 

 

 

 

 

 

 

600

 

 

 

 

 

 

 

600

 

 

 

 

 

.

 

15

596

70

min

 

5

5

 

820 min

 

176,5

0

 

 

818

416

12

 

 

 

 

 

1

 

 

 

 

 

54

 

 

 

 

 

8

1

 

 

 

 

95

 

 

 

 

 

 

 

 

 

160

 

 

 

 

 

0

 

 

 

 

165

9

 

 

 

 

0

 

 

A

P0965

49

 

 

 

 

 

When installing the appliance into the kitchen furniture ensure, if possible, the hoses are placed in either of the two recesses on the back of the appliance. This will help to prevent the hoses from becoming kinked or trapped. Picture AB.

Preparation and assembly of the door

The machine is originally pre-arranged for the assembly of a door opening from right to left.

In this case it is sufficient to screw in the hinges (1) and the counter-magnet (6) provided with the appliance, at the right level (Fig. B).

6

 

 

4

 

 

 

1

2

7

5

1

 

 

3

 

23

 

 

B

P0982

 

 

 

a) Door

The dimensions of the door should be:

- width 595-598 mm - thickness 16-22 mm

The height (C-Fig. C) depends on the height of the adjacent furniture's base.

35 Ø 12.5-14 depth

 

 

 

16

 

 

B

 

-

 

 

 

22

 

 

 

 

 

 

416

C

 

 

 

 

,5

 

 

 

+1

 

 

 

22

 

 

 

 

598

 

 

 

5-

 

 

 

59

 

 

P0422S

 

 

 

C

b) Hinges

To mount the hinges it is necessary to drill two holes (dia. 35 mm, depth 12.5-14 mm depending on the depth of door furniture) on the inner side of the door. The distance between the holes hobs fixing centres must be 416 mm.

The distance (B) from upper edge of the door to the centre of the hole depends on the adjacent furniture's dimensions.

The required dimensions are given in the picture C. The hinges will be fixed to the door by means of screws for wood (2-Fig. B) supplied with the appliance.

c) Mounting the door

Fix the hinges (1) to the machine by means of the M5x15 screws (3-Fig. B). The hinges can be adjusted to compensate for possible uneven thickness of the door. To align the door perfectly it is necessary to loosen the screw (3-Fig. B), adjust the door and tighten the screw again.

d) Counter-magnet (6)

The appliance is pre-arranged for a magnetic closure of the door. To enable a correct operation of this device, it is necessary to screw the counter-magnet (6) (steel disk + rubber ring) into the inner side of the door.

Its position must correspond to the magnet (4) on the appliance (see picture D).

 

6

 

4

P0984

D

 

26

Image 26
Contents Instruction Booklet Use InstallationChild Safety Contents Interest Environment Your New Washing MachineEcological hints Detergent dispenser drawer Child safety featureDescription of the Appliance Control Panel Operating Sequence To drain and spin, depress the Rinse Hold button again Start the programmeAt the end of the programme Select the required programme At the end of the programme Washing Hints 1000g = 1 kgWhich detergent? Which form?Wash Care Symbols Important NotesWashing Programmes Load Washing symbol Type of laundryWash programme Degree of soil Programme Description Maintenance and Cleaning Cleaning the water inlet filter Emergency emptying outSomething Not Working 0870 5 Service & Spare PartsSymptom Possible causes Customer CareEuropean guarantee Guarantee ConditionsStandard guarantee conditions This guarantee does not coverInstallation Instructions Technical SpecificationsPositioning Installation on a Suspended FloorUnpacking Appliance must be connected to a cold water supply Water inletWater drainage Into a drainage standpipeInterest of the environment LevellingSpecial conditions Onto a sink outlet spigotElectrical connection Permanent connectionPreparation and assembly of the door Building-inDrill four fixing holes see Fig. G