JVC RX-E11S manual Adjusting speaker output level, Adjusting the center tone-CENTER Tone

Page 23

Adjusting speaker output level

•SUBWFR LVL (subwoofer output level),

•FRONT L LVL (left front speaker output level),

•FRONT R LVL (right front speaker output level),

•CENTER LVL (center speaker output level),

•SURR L LVL (left surround speaker output level),

•SURR R LVL (right surround speaker output level)

You can adjust the speaker output levels.

Adjust all the speakers’ output levels so that you can listen sounds from all speakers at the same level.

•Once you have made an adjustment, it is memorized for each source.

Adjustable range: –10 (dB) to +10 (dB) (in 1 step intervals)

Initial setting: 0 (dB) for all speakers

NOTES

•If you have selected “NO” for a speaker (see page 16), the output level for the corresponding speaker is not adjustable.

•While using headphones, you can adjust only the left and right front speakers’ output level.

•If you change one of these settings (except the subwoofer output level) manually, the distance and output level set manually will be applied instead of those set by using Smart Surround Setup.

From the remote control:

1Press TEST TONE to check the speakers’ output balance.

“TEST L” starts flashing on the display, and a test tone comes out of the speakers in the following order:

EQ C.TONE

VIRTUAL SB AUDIO P. BASS

TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE

LPCM

L

C

R

 

PL

ATT

DOLBY D

S . WFR LFE

NEO : 6

HP

DTS AAC

 

 

 

 

 

DSP 3D

MHz

LS

SB

RS

96 / 24

AUTO SR

kHz

 

 

 

 

 

 

 

 

L

 

C

 

R

 

 

(Left front speaker) (Center speaker) (Right front speaker)

SW LS RS

(Subwoofer) (Left surround speaker) (Right surround speaker)

2Adjust the speaker output levels.

When you press the level adjustment buttons corresponding to each speaker once, the current level for the speaker appears on the display, and the test tone comes out of the speaker.

EX.: When adjusting output level for the center speaker: Press CENTER +/–.

The test tone comes out of the center speaker.

If no adjustment is done for about 4 seconds, the test tone comes out of the next speaker.

3Press TEST TONE again to stop the test tone.

NOTES

•You can adjust the speaker output levels without the test tone.

•No test tone is available when the HEADPHONE (or 3D HEADPHONE) mode is in use.

Adjusting the sound parameters for the Surround/DSP modes

You can adjust the Surround/DSP sound parameters to your

preference.

•For details about the Surround/DSP modes, see pages 25 to 29.

Adjusting the effect level for DSP modes—EFFECT

This setting is available only when one of the DSP modes (except ALL CH ST.) is in use. To activate DSP mode, see pages 28 and 29.

•Once you have made an adjustment, it is memorized for each DSP mode.

Adjustable range: 1 to 5 (in 1 step intervals)

Initial setting: EFFECT 3

As the number increases, the effect becomes stronger. Normally, select “3.”

Adjusting the panorama control for Pro Logic II Music—PANORAMA

This setting is available only when Pro Logic II Music is in use. To activate Pro Logic II Music, see pages 28 and 29.

•Once you have made an adjustment, it is memorized until you change the setting.

•You cannot use the remote control for this setting.

PANORAMA ON Select to add “wraparound” sound effect with side-wall image.

PANORAMAOFF Select to listen to originally recorded sound.

Initial setting: PANORAMAOFF

Adjusting the center tone—CENTER TONE

This setting is available when one of the Surround/DSP modes is in use.

•If you have set “CENTER SPK” to “NO” (see page 16), the center tone is not adjustable.

•This setting is common to all Surround modes, and is memorized separately for DSP modes.

Adjustable range: 1 to 5 (in 1 step intervals)

Initial setting: CNT TONE 3

As the number increases, the dialogue becomes stronger. Normally, select “3.”

•When the center tone is set to other than “CNT TONE 3,” the C.TONE indicator lights up on the display.

From the remote control:

To adjust the effect level:

Press SOUND, then press EFFECT repeatedly.

To adjust the center tone:

Press SOUND, then press C.TONE repeatedly.

NOTE

After pressing SOUND, the numeric buttons work for sound adjustments. To use the numeric buttons to operate your target source, press the corresponding source selecting button before operation; otherwise, the remote control may not work as you intend.

Sound adjustments

21

Page 22 Page 24
Image 23
Page 22 Page 24
Contents US, UN, UX RX-E11SFront Stand height 15 cm or more Floor RX-E11STable of Contents AUDIO, DVR/DVD , VCR , DBS , TV Remote controlTUNING, FM MODE, Tuning 9, Memory Parts identificationFront panel Display windowRear panel Setting the voltage selector Before InstallationPutting batteries in the remote control Checking the supplied accessoriesFM antenna supplied Connecting the FM and AM antennasAM antenna connection FM antenna connectionConnecting the front, center, and surround speakers Connecting the speakersConnecting the subwoofer Speaker Layout DiagramNot supplied Connecting video componentsConnecting a TV Connecting a DVD recorder or DVD playerCable not supplied Connecting a VCRConnecting a DBS tuner Video cableDigital connection Connecting the power cordBasic operations Turn on the powerTo turn off the power into standby Selecting the analog or digital input modeListening with headphones Adjust the volumeSelecting the digital decode mode Press Dimmer repeatedly Adjusting the subwoofer audio positionTurning off the sounds temporarily Changing the display brightnessFrom the remote control only Press Sleep repeatedly Turning off the power with the Sleep TimerBasic adjustment of auto memory Signal and speaker indicators on the displayWhen your clapping sound is detected successfully Basic settingsFrom the remote control only Take your position where you listen to the soundBasic setting items Setting subwoofer information-SUBWOOFER Operating procedureSetting the speakers Setting the crossover frequency-CROSS Over Setting bass soundSetting the speaker distance Setting subwoofer output-SUBWFR OUTSelecting the main or sub channel Setting the virtual surround back speaker-VIRTUAL SBUsing the Midnight mode From the remote controlAuto SR on DVR/DVDDBS VCRTurn Multi JOG to adjust the selected item Sound adjustmentsBasic adjustment items Press AdjustAdjusting the effect level for DSP modes-EFFECT Adjusting speaker output levelAdjusting the center tone-CENTER Tone Reinforcing the bass-BASS Boost Adjusting the bass soundsSelecting the subwoofer sound phase-SBWFR Phase Attenuating the input signal-INPUT ATTTuner operations Tuning in to stations manuallyUsing preset tuning To store the preset stationsPress Tuner Preset Selecting the FM reception modeTo tune in a preset station From the remote control Press FM or AMDolby Digital Creating realistic sound fieldsReproducing theater ambience Introducing the Surround modesDTS Digital Surround 3D Headphone modeAbout other digital signals DTSDigital Acoustic Processor DAP modes All Channel Stereo mode ALL CH STIntroducing the DSP modes If Auto Surrnd Auto Surround is set to on Using the Surround/DSP modesTo cancel Surround/DSP modes Select and play any source you likeDTS THEATER1/2, ALL CH ST.*2 DTS-ES Headphone Surrnd OFF Dolby DDolby D HALL1/2, Live Club Dance CLUB, PavilionMonaural mini-plugs Not supplied AV Compu Link remote control systemConnections 1 AV Compu Link connection Connections 2 Video cable connectionOne-touch video play Connecting procedureAutomatic selection of TV’s input mode Automatic power on/offChannel + Operating other JVC productsTurn on or off the TV Turn on or off the VCRTOP MENU/MENU DVD recorder or DVD playerTry to operate your TV by pressing TV Changing the transmittable signals for operating a TVOperating other manufacturers’ products Release TVManufacturers’ codes for VCR Changing the transmittable signals for operating a VCRRelease VCR Try to operate your VCR by pressing VCRRelease DVR/DVD Release DBSTry to operate your DBS tuner by pressing DBS Manufacturers’ codes for DBS tunerTuner TroubleshootingPower SoundAM tuner SpecificationsAmplifier FM tuner IHF0105RYMMDWJEIN Victor Company of Japan, Limited

RX-E11S specifications

The JVC RX-E11S is an exceptional integrated stereo receiver that artfully blends both performance and stylistic aesthetics, making it a popular choice for audiophiles and casual listeners alike. As a part of JVC's renowned line of audio equipment, the RX-E11S integrates the latest technologies to deliver an unparalleled listening experience.

At the heart of the RX-E11S is its robust power amplification system. It boasts an impressive output power rating, delivering clear and dynamic sound across a wide range of frequencies. Whether you are indulging in classical music, rock, or contemporary genres, the receiver maintains rich detail and clarity while providing sufficient power to drive a variety of speakers.

One of the standout features of the RX-E11S is its advanced digital signal processing technology. This allows for various sound enhancement options that cater to different listening environments and personal preferences. The receiver includes numerous preset equalizer settings and the capability to configure custom sound profiles, ensuring that users can achieve their desired sound signature.

The RX-E11S supports multiple audio inputs, including traditional analog connections and digital interfaces such as USB and optical inputs. This versatility enables seamless integration with a wide range of devices, from vinyl turntables to modern digital media players. The inclusion of Bluetooth technology also allows for wireless streaming from smartphones, tablets, or computers, providing users ease of access to their favorite playlists without the need for cumbersome cabling.

In terms of build quality, the JVC RX-E11S features a sleek and modern design that fits elegantly into any home audio setup. Its intuitive control layout includes a user-friendly interface, making it straightforward for users to navigate through settings and input selections. Additionally, the receiver houses a high-quality FM/AM tuner, allowing for easy access to a variety of radio stations.

The RX-E11S places a strong emphasis on flexibility and convenience, offering features such as a programmable timer and sleep function. This capability adds to the user experience, making it possible to enjoy music before bedtime or wake up to favorite tunes.

In summary, the JVC RX-E11S is a highly versatile and well-equipped stereo receiver that excels in delivering high-fidelity audio performance with modern technology. With its comprehensive features and elegant design, it serves as an excellent centerpiece for any home audio system. Whether you're an audiophile seeking precision sound or a casual listener looking for enjoyable listening sessions, the RX-E11S is poised to meet and exceed expectations.
Top Page Image Contents