JVC RX-E11S manual Troubleshooting, Power, Sound, Tuner

Page 39

Troubleshooting

Use this chart to help you solve daily operational problems. If there are any problems you cannot solve, contact your JVC’s service center.

Power

The power does not come on.

\The power cord is not plugged in. Plug the power cord into an AC outlet.

The receiver turns off (enters standby mode).

\Speakers are overloaded because of high volume.

1.Stop the playback source.

2.Turn on the receiver again, then turn the volume down.

\Speakers are overloaded because of a short circuit at the speaker terminals. Check the speaker wiring.

If speaker wiring is not short-circuited, contact your dealer.

\The receiver is overloaded because of a high voltage. Consult your dealer after unplugging the power cord.

“OVER HEAT” flashes on the display, then the receiver turns off.

\The receiver is overheated because of high volume or long time usage.

Turn on the receiver again. If the receiver turns off soon, consult your dealer after unplugging the power cord.

Sound

No sound from speakers.

\Speaker signal cables are not connected. Check speaker wiring, then reconnect if necessary (see page 6) after unplugging the power cord.

\Connections are incorrect. Check the audio connections (see pages 7 to 9) after unplugging the power cord.

\An incorrect source is selected. Select the correct source.

\Muting is activated. Press MUTING to cancel the mute (see page 12).

\An incorrect input mode (analog or digital) is selected. Select the correct input mode (analog or digital).

Sound from one speaker only.

\Speaker signal cables are not connected properly. Check speaker wiring and reconnect if necessary (see page 6) after unplugging the power cord.

Bass sound is reinforced too much when listening in stereo.

\Adjust audio position level (see page 12).

Sounds are intermittently distorted by the outside noise such as a lightning discharge.

\When you use the digital coaxial connection, the sounds may be intermittently distorted by the outside noise such as a lightning discharge but the sound will be restored automatically. This is not a malfunction.

Remote control

Remote control does not operate as you intend.

\The remote control is not ready for your intended operation. Set the mode selector correctly, then press the corresponding source selecting button or SOUND before operation.

Remote control does not work.

\There is an obstruction hiding the remote sensor on the receiver. Remove the obstruction.

\Batteries are weak. Replace batteries.

\The mode selector is set to the incorrect position. Set the mode selector to the proper position.

Tuner

Continuous hiss or buzzing during FM reception.

\Incoming signal is too weak. Connect an outdoor FM antenna or contact your dealer.

\The station is too far away. Select another station.

\The wrong antenna is being used. Check with your dealer to be sure you have the correct antenna.

\Antennas are not connected properly. Check the connections.

Occasional cracking noise during FM reception.

\Ignition noise from automobiles. Move the antenna farther from automobile traffic.

Troubleshooting

37

Page 38 Page 40
Image 39
Page 38 Page 40
Contents US, UN, UX RX-E11SFront Stand height 15 cm or more Floor RX-E11STable of Contents AUDIO, DVR/DVD , VCR , DBS , TV Remote controlTUNING, FM MODE, Tuning 9, Memory Parts identificationDisplay window Rear panelFront panel Setting the voltage selector Before InstallationPutting batteries in the remote control Checking the supplied accessoriesFM antenna supplied Connecting the FM and AM antennasAM antenna connection FM antenna connectionConnecting the front, center, and surround speakers Connecting the speakersConnecting the subwoofer Speaker Layout DiagramNot supplied Connecting video componentsConnecting a TV Connecting a DVD recorder or DVD playerCable not supplied Connecting a VCRConnecting a DBS tuner Video cableDigital connection Connecting the power cordBasic operations Turn on the powerTo turn off the power into standby Selecting the analog or digital input modeAdjust the volume Selecting the digital decode modeListening with headphones Press Dimmer repeatedly Adjusting the subwoofer audio positionTurning off the sounds temporarily Changing the display brightnessFrom the remote control only Press Sleep repeatedly Turning off the power with the Sleep TimerBasic adjustment of auto memory Signal and speaker indicators on the displayWhen your clapping sound is detected successfully Basic settingsFrom the remote control only Take your position where you listen to the soundBasic setting items Operating procedure Setting the speakersSetting subwoofer information-SUBWOOFER Setting the crossover frequency-CROSS Over Setting bass soundSetting the speaker distance Setting subwoofer output-SUBWFR OUTSelecting the main or sub channel Setting the virtual surround back speaker-VIRTUAL SBUsing the Midnight mode From the remote controlAuto SR on DVR/DVDDBS VCRTurn Multi JOG to adjust the selected item Sound adjustmentsBasic adjustment items Press AdjustAdjusting speaker output level Adjusting the center tone-CENTER ToneAdjusting the effect level for DSP modes-EFFECT Reinforcing the bass-BASS Boost Adjusting the bass soundsSelecting the subwoofer sound phase-SBWFR Phase Attenuating the input signal-INPUT ATTTuner operations Tuning in to stations manuallyUsing preset tuning To store the preset stationsPress Tuner Preset Selecting the FM reception modeTo tune in a preset station From the remote control Press FM or AMDolby Digital Creating realistic sound fieldsReproducing theater ambience Introducing the Surround modesDTS Digital Surround 3D Headphone modeAbout other digital signals DTSAll Channel Stereo mode ALL CH ST Introducing the DSP modesDigital Acoustic Processor DAP modes If Auto Surrnd Auto Surround is set to on Using the Surround/DSP modesTo cancel Surround/DSP modes Select and play any source you likeDTS THEATER1/2, ALL CH ST.*2 DTS-ES Headphone Surrnd OFF Dolby DDolby D HALL1/2, Live Club Dance CLUB, PavilionMonaural mini-plugs Not supplied AV Compu Link remote control systemConnections 1 AV Compu Link connection Connections 2 Video cable connectionOne-touch video play Connecting procedureAutomatic selection of TV’s input mode Automatic power on/offChannel + Operating other JVC productsTurn on or off the TV Turn on or off the VCRTOP MENU/MENU DVD recorder or DVD playerTry to operate your TV by pressing TV Changing the transmittable signals for operating a TVOperating other manufacturers’ products Release TVManufacturers’ codes for VCR Changing the transmittable signals for operating a VCRRelease VCR Try to operate your VCR by pressing VCRRelease DVR/DVD Release DBSTry to operate your DBS tuner by pressing DBS Manufacturers’ codes for DBS tunerTuner TroubleshootingPower SoundAM tuner SpecificationsAmplifier FM tuner IHF0105RYMMDWJEIN Victor Company of Japan, Limited

RX-E11S specifications

The JVC RX-E11S is an exceptional integrated stereo receiver that artfully blends both performance and stylistic aesthetics, making it a popular choice for audiophiles and casual listeners alike. As a part of JVC's renowned line of audio equipment, the RX-E11S integrates the latest technologies to deliver an unparalleled listening experience.

At the heart of the RX-E11S is its robust power amplification system. It boasts an impressive output power rating, delivering clear and dynamic sound across a wide range of frequencies. Whether you are indulging in classical music, rock, or contemporary genres, the receiver maintains rich detail and clarity while providing sufficient power to drive a variety of speakers.

One of the standout features of the RX-E11S is its advanced digital signal processing technology. This allows for various sound enhancement options that cater to different listening environments and personal preferences. The receiver includes numerous preset equalizer settings and the capability to configure custom sound profiles, ensuring that users can achieve their desired sound signature.

The RX-E11S supports multiple audio inputs, including traditional analog connections and digital interfaces such as USB and optical inputs. This versatility enables seamless integration with a wide range of devices, from vinyl turntables to modern digital media players. The inclusion of Bluetooth technology also allows for wireless streaming from smartphones, tablets, or computers, providing users ease of access to their favorite playlists without the need for cumbersome cabling.

In terms of build quality, the JVC RX-E11S features a sleek and modern design that fits elegantly into any home audio setup. Its intuitive control layout includes a user-friendly interface, making it straightforward for users to navigate through settings and input selections. Additionally, the receiver houses a high-quality FM/AM tuner, allowing for easy access to a variety of radio stations.

The RX-E11S places a strong emphasis on flexibility and convenience, offering features such as a programmable timer and sleep function. This capability adds to the user experience, making it possible to enjoy music before bedtime or wake up to favorite tunes.

In summary, the JVC RX-E11S is a highly versatile and well-equipped stereo receiver that excels in delivering high-fidelity audio performance with modern technology. With its comprehensive features and elegant design, it serves as an excellent centerpiece for any home audio system. Whether you're an audiophile seeking precision sound or a casual listener looking for enjoyable listening sessions, the RX-E11S is poised to meet and exceed expectations.
Top Page Image Contents