Whirlpool W10151492A manual Install VentSystem, Install LevelingLegs, ConnectVent, LevelDryer

Page 14

Vent system chart

NOTE: Performance of rear exhaust to either side of the dryer is equivalent to adding one elbow. To determine maximum exhaust length, add one elbow to the chart.

Number of

Type of

Box or

Angled

90º turns

vent

Louvered

hoods

or elbows

 

hoods

 

 

 

 

 

0

Rigid metal

64 ft (20 m)

58 ft (17.7 m)

 

Flexible metal

36 ft (11 m)

28 ft (8.5 m)

 

 

 

 

1

Rigid metal

54 ft (16.5 m)

48 ft (14.6 m)

 

Flexible metal

31 ft (9.4 m)

23 ft (7 m)

 

 

 

 

2

Rigid metal

44 ft (13.4 m)

38 ft (11.6 m)

 

Flexible metal

27 ft (8.2 m)

19 ft (5.8 m)

 

 

 

 

3

Rigid metal

35 ft (10.7 m)

29 ft (8.8 m)

 

Flexible metal

25 ft (7.6 m)

17 ft (5.2 m)

 

 

 

 

4

Rigid metal

27 ft (8.2 m)

21 ft (6.4 m)

 

Flexible metal

23 ft (7 m)

15 ft (4.6 m)

Install VentSystem

1.Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood.

2.Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

3.Run vent to dryer location. Use the straightest path possible. See “Determine vent path” in “Plan Vent System.” Avoid 90º turns. Use clamps to seal all joints. Do not use duct tape, screws or other fastening devices that extend into the interior of the vent to secure vent.

Install LevelingLegs

WARNING

Excessive Weight Hazard

Use two or more people to move and install dryer. Failure to do so can result in back or other injury.

1.To protect the floor, use a large, flat piece of cardboard from the dryer carton. Place cardboard under the entire back edge of the dryer.

2.Firmly grasp the body of the dryer (not the top or console panel). Gently lay the dryer on the cardboard. See illustration.

3.Examine the leveling legs. Find the diamond marking.

4.Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the diamond marking is no longer visible.

5.Place a carton corner post from dryer packaging under each of the 2 dryer back corners. Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location. Leave enough room to connect the exhaust vent.

ConnectVent

1.Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Check that the vent is secured to exhaust hood with a 4" (10.2 cm) clamp.

2.Move dryer into its final location. Do not crush or kink vent.

3.(On gas models) Check that there are no kinks in the flexible gas line.

4.Once the exhaust vent connection is made, remove the corner posts and cardboard.

LevelDryer

Check the levelness of the dryer by first placing a level on the top of the dryer near the console.

Then, by placing a level in the crease on the side of the dryer between the top of the dryer and the dryer cabinet, check the levelness from front to back.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness.

14

Image 14
Contents System Electric Dryer W10151492ATable DES Matières Dryer Safety Your safety and the safety of others are very importantLocationRequirements Installation InstructionsToolsandParts ElectricalRequirements -U.S.A.Only Mobile home Additional installation requirementsMobile home installations require Electrical ConnectionIf connecting by direct wire ElectricalRequirements-CanadaOnlyElectricalConnection-U.S.A.Only Power Supply Cord Direct WireStyle 1 Power supply cord strain relief Wire connection Power supply cord Style 2 Direct wire strain reliefWire connection Direct Wire Remove center silver-colored terminal block screwBDE CG F Optional 3-wire connection If this is a new vent system Vent material If using an existing vent systemVentingRequirements PlanVentSystem Alternate installations for close clearancesSpecial provisions for mobile home installations Determine vent pathVent system chart Install VentSystemInstall LevelingLegs ConnectVentReverseDoorSwing Remove the door assemblyReinstall the door Reverse the strikeCanada CompleteInstallationU.S.A If the dryer will not start, check the followingTo use an Automatic Cycle Dryer USEStartingYourDryer To make changes during an Automatic CycleStatusLights Stopping,PausingorRestartingDryingandCycleTips Cycles Modifiers Options ChangingCycles,Modifiers AndOptions EndofCycleSignalDryingRackOption Dryer Care DryerOperation TroubleshootingChangingtheDrumLight Lint on load DryerResultsCycle time too short IntheU.S.A Assistance or ServiceAccessories InCanadaWhirlpool Corporation Major Appliance Warranty CallPage Sécurité DE LA Sécheuse Votre sécurité et celle des autres est très importanteOutillageetpièces Instructions D’INSTALLATIONExigences d’emplacement Exigencesconcernantlévacuation Linstallation dans une maison mobile exigeSpécificationsélectriques-PourleCanada Seulement ’est à l’utilisateur qu’incombe la responsabilité deEn cas dutilisation du système dévacuation existant Déterminer litinéraire dacheminement du conduit Autres installations où le dégagement est réduitPlanificationdusystèmed’évacuation Raccordementduconduitd’évacuation Installationdusystèmed’évacuationInstallationdespiedsdenivellement Réglagedelaplomb dela sécheuseDépose de la porte Réinstallation de la porteInversiondusens douverturedelaporte Inversion de la gâcheAcheverlinstallation Si la sécheuse ne démarre pas, vérifier ce qui suitUtilisation dun programme automatique Utilisation DE LA SécheuseMiseenmarchedelasécheuse Pour mettre la sécheuse en pause ou larrêter à tout moment Arrêt,pauseouremiseenmarcheConseils pourleséchageetles programmes Pour remettre la sécheuse en marcheTémoins lumineux ProgrammesModificateurs Signaldefindeprogramme Modification des préréglages de niveau de séchage OptiondegrilledeséchageChangement des programmes après avoir appuyé sur Start Utilisation de la grille de séchageNettoyage avant chaque charge NettoyagedelemplacementdelasécheuseNettoyagedufiltreàcharpie Précautionsàprendrepourlesvacancesetavantun Déménagement Nettoyagedel’intérieurdelasécheuseRetraitdelacharpieaccumulée Changementdel’ampouled’éclairage DutambourRésultatsdelasécheuse DépannageFonctionnementdelasécheuse Taches sur la charge ou sur le tambour Temps de programme trop courtCharpie sur la charge Charges avec faux plisPour plus d’assistance AccessoiresSi vous avez besoin de pièces de rechange Garantie DES Gros Appareils Ménagers Whirlpool Corporation Garantie Limitée DE UN ANW10151492A SP PN W10151493A Whirlpool Corporation All rights reserved
Related manuals
Manual 48 pages 36.57 Kb

W10151493A, W10151492A specifications

The Whirlpool W10151492A and W10151493A are innovative appliances designed to enhance convenience and efficiency in modern kitchens. Both models are part of Whirlpool's commitment to delivering top-quality home solutions that simplify everyday tasks.

One of the standout features of the W10151492A and W10151493A is the advanced technology that ensures optimal performance. These units are equipped with a powerful motor that provides superior cleaning results, making them ideal for tackling tough stains and grime. The appliances also utilize innovative washing methods that maximize water and energy efficiency, thus reducing the overall environmental impact and utility bills.

The W10151492A and W10151493A are designed with user-friendly controls, allowing homeowners to easily navigate through various settings and customize each wash cycle to their specific needs. The intuitive interface provides clear indicators and options, making it simple for anyone to operate the appliance without a steep learning curve.

Another notable characteristic of these models is their spacious capacity. With ample interior space, users can wash larger loads in a single cycle, making them perfect for families or those who frequently entertain guests. The stainless steel drum not only ensures longevity and resistance to stains but also enhances the overall aesthetic of the appliance, providing a sleek and modern look.

These models also incorporate smart technology features, allowing users to monitor and control their appliances remotely. Whether it’s starting a load from a smartphone or receiving notifications when the wash is complete, these conveniences align perfectly with today’s fast-paced lifestyle.

Moreover, the sound-dampening technology minimizes noise during operation, ensuring that the appliances function quietly in the background, allowing for an undisturbed home environment. This is especially important in open-concept living spaces, where noise from kitchen appliances can disrupt daily activities.

In summary, the Whirlpool W10151492A and W10151493A not only boast impressive technology and features that cater to modern-day convenience but also prioritize efficiency, capacity, and user-friendliness. With these models, consumers can expect quality performance that aligns with their busy lifestyles while contributing to a more sustainable home.