Whirlpool W10151492A, W10151493A ElectricalRequirements-CanadaOnly, If connecting by direct wire

Page 6

If your outlet looks like this:

3-wire receptacle (10-30R)

Then choose a 3-wire power supply cord with ring or spade terminals and UL listed strain relief. The 3-wire power supply cord, at least 4 ft (1.22 m) long, must have three 10-gauge copper wires and match a 3-wire receptacle of NEMA Type 10-30R.

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire) and be:

■Flexible armored cable or nonmetallic sheathed copper cable (with ground wire), protected with flexible metallic conduit. All current-carrying wires must be insulated.

■10-gauge solid copper wire (do not use aluminum).

■At least 5 ft (1.52 m) long.

GROUNDING INSTRUCTIONS

■For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

This dryer uses a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

■For a permanently connected dryer:

This dryer must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the dryer.

WARNING: Improper connection of the equipment- grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug on the power supply cord: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

ElectricalRequirements-CanadaOnly

WARNING

Electrical Shock Hazard

Plug into a grounded 4 prong outlet.

Failure to do so can result in death or electrical shock.

It is your responsibility

■To contact a qualified electrical installer.

■To be sure that the electrical connection is adequate and in conformance with the Canadian Electrical Code, C22.1-latest edition and all local codes. A copy of the above codes standard may be obtained from: Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3

CANADA.

■To supply the required 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit.

■This dryer is equipped with a CSA International Certified Power Cord intended to be plugged into a standard 14-30R wall receptacle. The cord is 5 ft (1.52 m) in length. Be sure wall receptacle is within reach of dryer’s final location.

4-wire receptacle 14-30R

■Do not use an extension cord.

If you are using a replacement power supply cord, it is recommended that you use Power Supply Cord Replacement Part Number 3394208. For further information, please reference the service numbers located in the “Assistance or Service” section.

GROUNDING INSTRUCTIONS

■For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment- grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment- grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug provided with the dryer: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents System Electric Dryer W10151492ATable DES Matières Dryer Safety Your safety and the safety of others are very importantInstallation Instructions ToolsandPartsLocationRequirements ElectricalRequirements -U.S.A.Only Mobile home Additional installation requirementsMobile home installations require Electrical ConnectionIf connecting by direct wire ElectricalRequirements-CanadaOnlyPower Supply Cord Direct Wire Style 1 Power supply cord strain reliefElectricalConnection-U.S.A.Only Wire connection Power supply cord Style 2 Direct wire strain reliefWire connection Direct Wire Remove center silver-colored terminal block screwBDE CG F Optional 3-wire connection If using an existing vent system VentingRequirementsIf this is a new vent system Vent material PlanVentSystem Alternate installations for close clearancesSpecial provisions for mobile home installations Determine vent pathVent system chart Install VentSystemInstall LevelingLegs ConnectVentReverseDoorSwing Remove the door assemblyReinstall the door Reverse the strikeCanada CompleteInstallationU.S.A If the dryer will not start, check the followingTo use an Automatic Cycle Dryer USEStartingYourDryer To make changes during an Automatic CycleStopping,PausingorRestarting DryingandCycleTipsStatusLights Cycles Modifiers Options EndofCycleSignal DryingRackOptionChangingCycles,Modifiers AndOptions Dryer Care Troubleshooting ChangingtheDrumLightDryerOperation DryerResults Cycle time too shortLint on load IntheU.S.A Assistance or ServiceAccessories InCanadaWhirlpool Corporation Major Appliance Warranty CallPage Sécurité DE LA Sécheuse Votre sécurité et celle des autres est très importanteInstructions D’INSTALLATION Exigences d’emplacementOutillageetpièces Exigencesconcernantlévacuation Linstallation dans une maison mobile exigeSpécificationsélectriques-PourleCanada Seulement ’est à l’utilisateur qu’incombe la responsabilité deEn cas dutilisation du système dévacuation existant Autres installations où le dégagement est réduit Planificationdusystèmed’évacuationDéterminer litinéraire dacheminement du conduit Raccordementduconduitd’évacuation Installationdusystèmed’évacuationInstallationdespiedsdenivellement Réglagedelaplomb dela sécheuseDépose de la porte Réinstallation de la porteInversiondusens douverturedelaporte Inversion de la gâcheAcheverlinstallation Si la sécheuse ne démarre pas, vérifier ce qui suitUtilisation DE LA Sécheuse MiseenmarchedelasécheuseUtilisation dun programme automatique Pour mettre la sécheuse en pause ou larrêter à tout moment Arrêt,pauseouremiseenmarcheConseils pourleséchageetles programmes Pour remettre la sécheuse en marcheTémoins lumineux ProgrammesModificateurs Signaldefindeprogramme Modification des préréglages de niveau de séchage OptiondegrilledeséchageChangement des programmes après avoir appuyé sur Start Utilisation de la grille de séchageNettoyagedelemplacementdelasécheuse NettoyagedufiltreàcharpieNettoyage avant chaque charge Précautionsàprendrepourlesvacancesetavantun Déménagement Nettoyagedel’intérieurdelasécheuseRetraitdelacharpieaccumulée Changementdel’ampouled’éclairage DutambourDépannage FonctionnementdelasécheuseRésultatsdelasécheuse Taches sur la charge ou sur le tambour Temps de programme trop courtCharpie sur la charge Charges avec faux plisAccessoires Si vous avez besoin de pièces de rechangePour plus d’assistance Garantie DES Gros Appareils Ménagers Whirlpool Corporation Garantie Limitée DE UN ANW10151492A SP PN W10151493A Whirlpool Corporation All rights reserved
Related manuals
Manual 48 pages 36.57 Kb

W10151493A, W10151492A specifications

The Whirlpool W10151492A and W10151493A are innovative appliances designed to enhance convenience and efficiency in modern kitchens. Both models are part of Whirlpool's commitment to delivering top-quality home solutions that simplify everyday tasks.

One of the standout features of the W10151492A and W10151493A is the advanced technology that ensures optimal performance. These units are equipped with a powerful motor that provides superior cleaning results, making them ideal for tackling tough stains and grime. The appliances also utilize innovative washing methods that maximize water and energy efficiency, thus reducing the overall environmental impact and utility bills.

The W10151492A and W10151493A are designed with user-friendly controls, allowing homeowners to easily navigate through various settings and customize each wash cycle to their specific needs. The intuitive interface provides clear indicators and options, making it simple for anyone to operate the appliance without a steep learning curve.

Another notable characteristic of these models is their spacious capacity. With ample interior space, users can wash larger loads in a single cycle, making them perfect for families or those who frequently entertain guests. The stainless steel drum not only ensures longevity and resistance to stains but also enhances the overall aesthetic of the appliance, providing a sleek and modern look.

These models also incorporate smart technology features, allowing users to monitor and control their appliances remotely. Whether it’s starting a load from a smartphone or receiving notifications when the wash is complete, these conveniences align perfectly with today’s fast-paced lifestyle.

Moreover, the sound-dampening technology minimizes noise during operation, ensuring that the appliances function quietly in the background, allowing for an undisturbed home environment. This is especially important in open-concept living spaces, where noise from kitchen appliances can disrupt daily activities.

In summary, the Whirlpool W10151492A and W10151493A not only boast impressive technology and features that cater to modern-day convenience but also prioritize efficiency, capacity, and user-friendliness. With these models, consumers can expect quality performance that aligns with their busy lifestyles while contributing to a more sustainable home.
Top Page Image Contents