Installation Instructions, ToolsandParts

INSTALLATION INSTRUCTIONS

ToolsandParts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

LocationRequirements

WARNING

■Flat-blade screwdriver

■#2 Phillips screwdriver

■Adjustable wrench that opens to 1" (2.5 cm) or hex-head socket wrench (for adjusting dryer feet)

■Wire stripper (direct wire installations)

■Tin snips (new vent installations)

■Level

■Vent clamps

■Caulking gun and compound (for installing new exhaust vent)

■Tape measure

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Parts supplied:

Remove parts package from dryer drum. Check that all parts were included.

Place dryer at least 18 inches (46 cm) above the floor for a garage installation.

Failure to do so can result in death, explosion, or fire.

4 leveling legs

Parts needed:

Check local codes. Check existing electrical supply and venting and see “Electrical Requirements” and “Venting Requirements” before purchasing parts.

Mobile home installations require metal exhaust system hardware available for purchase from the dealer from whom you purchased your dryer. For information on ordering, please refer to the “Assistance or Service” section. You may also contact the dealer from whom you purchased your dryer.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain:

■A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at least 4 ft (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends.

■A UL listed strain relief.

You will need

■A location that allows for proper exhaust installation. See “Venting Requirements.”

■A separate 30-amp circuit.

■If you are using a power supply cord, a grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See “Electrical Requirements.”

■A sturdy floor to support the total weight (dryer and load) of 200 lbs (90.7 kg). The combined weight of a companion appliance should also be considered.

■A level floor with a maximum slope of 1" (2.5 cm) under entire dryer.

Do not operate your dryer at temperatures below 45ºF (7ºC). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.

Installation Clearances

The location must be large enough to allow the dryer door to open fully.

Dryer Dimensions

43½"

(110.5 cm)

	22¼"
*29¼"	(56.5 cm)
(74.3 cm)	29"
	29"
	(73.7 cm)

*Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for the exhaust vent with elbow. See “Venting Requirements.”

W10151493A, W10151492A specifications

The Whirlpool W10151492A and W10151493A are innovative appliances designed to enhance convenience and efficiency in modern kitchens. Both models are part of Whirlpool's commitment to delivering top-quality home solutions that simplify everyday tasks.

One of the standout features of the W10151492A and W10151493A is the advanced technology that ensures optimal performance. These units are equipped with a powerful motor that provides superior cleaning results, making them ideal for tackling tough stains and grime. The appliances also utilize innovative washing methods that maximize water and energy efficiency, thus reducing the overall environmental impact and utility bills.

The W10151492A and W10151493A are designed with user-friendly controls, allowing homeowners to easily navigate through various settings and customize each wash cycle to their specific needs. The intuitive interface provides clear indicators and options, making it simple for anyone to operate the appliance without a steep learning curve.

Another notable characteristic of these models is their spacious capacity. With ample interior space, users can wash larger loads in a single cycle, making them perfect for families or those who frequently entertain guests. The stainless steel drum not only ensures longevity and resistance to stains but also enhances the overall aesthetic of the appliance, providing a sleek and modern look.

These models also incorporate smart technology features, allowing users to monitor and control their appliances remotely. Whether it’s starting a load from a smartphone or receiving notifications when the wash is complete, these conveniences align perfectly with today’s fast-paced lifestyle.

Moreover, the sound-dampening technology minimizes noise during operation, ensuring that the appliances function quietly in the background, allowing for an undisturbed home environment. This is especially important in open-concept living spaces, where noise from kitchen appliances can disrupt daily activities.

In summary, the Whirlpool W10151492A and W10151493A not only boast impressive technology and features that cater to modern-day convenience but also prioritize efficiency, capacity, and user-friendliness. With these models, consumers can expect quality performance that aligns with their busy lifestyles while contributing to a more sustainable home.