Whirlpool 8TCEM2760KQ0 installation instructions What to do if YOU Smell GAS

Page 3

WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, or to prevent property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

Clear the room, building, or area of all occupants.

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

In the State of Massachusetts, the following installation instructions apply:

Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by the State of Massachusetts.

If using a ball valve, it shall be a T-handle type.

A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions, including the following:

Read all instructions before using the dryer.

Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry- cleaning solvents, other flammable, or explosive substances as they give off vapors that could ignite or explode.

Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is used near children.

Before the dryer is removed from service or discarded, remove the door to the drying compartment.

Do not reach into the dryer if the drum is moving.

Do not install or store the dryer where it will be exposed to the weather.

Do not tamper with controls.

Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair instruc- tions that you understand and have the skills to carry out.

Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

Clean lint screen before or after each load.

Keep area around the exhaust opening and adjacent sur- rounding areas free from the accumulation of lint,dust, and dirt.

The interior of the dryer and exhaust vent should be cleaned periodically by qualified service personnel.

See installation instructions for grounding requirements.

SAVE THESE INSTRUCTIONS

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

3

Image 3
Contents Installation Instructions Dryer Safety What to do if YOU Smell GAS Tools needed Recessed Area and Closet Installation InstructionsTools and Parts Location RequirementsProduct Dimensions 29 73.7 cm dryer Product Dimensions 27 68.6 cm dryerElectrical Requirements Gas Dryer Electrical Requirements Electric DryerRecommended Ground Method Type of Gas Gas Supply RequirementsGas Supply Pressure Testing Venting RequirementsGas Supply Line Maximum Vent Length Vent System Length Multiple Dryer VentingInstall Coin Slide and Coin Box Complete InstallationConnect Vent Make Electrical Connection Power Supply Cord Method U.S. OnlyPower Supply Cord, Four-wire electrical connection EDC Power Supply Cord, Three-wire electrical connectionDirect Wire Four-wire electrical connection Direct Wire Method U.S. OnlyLoosen or remove the center terminal block screw Direct Wire Three-wire electrical connectionChanging to a 30- or 60-MINUTE Timing CAM Maintenance instructions 2006 05/2006 W10103110 Page Page Page 35.6 cm 38.1 cm 27 68.6 cm 5 cm Page Page Page No. of 90 turns Page Page Page EDC ¹⁄₂ 8.9 cm 12.7 cm 2 8.9 cm Page Page W10103110