Operating other manufacturers’ VCR, Release VCR

Operating other manufacturers’ VCR

By changing the remote control signals from preset ones to the other manufacturers’, you can use the remote control supplied for this system to operate other manufacturers’ VCRs.

•You can also operate other manufacturers’ TVs using the remote control supplied with this system. (See page 20.)

•When operating other manufacturers’ VCR, aim the remote control directly at the remote control sensor on your VCR. Refer also to the instruction manuals supplied with your VCR.

		TV	AUDIO
AUX	FM/AM	DVD	VCR1	VCR
				VCR
AUDIO	ANGLE	SUBTITLE	DECODE	button
				button
RETURN	DIGEST	ZOOM	VFP
		+
TOP MENU	MENU	ZOOM

–SOUND

CONTROL	– SUBWOOFER +			EFFECT
VCR	1		2	3
	–	CENTER	+	TEST
TV	4		5	6	Number buttons
SLEEP	–	REAR-L	+		Number buttons
SLEEP	–	REAR-L	+
	7		8	9
SETTING	–	REAR-R	+
	10		0	+10	VCR CONTROL
	TV RETURN FM MODE			100+	VCR CONTROL
SCREEN	TA/NEWS/INFO				button
ON
				DVD	Remote control
				RDS	Remote control
PTY(		ENTER		PTY9	mode selector
		ENTER		SURROUND
CHOICE				MODE

RDS DISPLAY

PTY SEARCH

7Setting the remote control signal for operating your

VCR.

•You can operate your VCR without setting the remote control signal if your VCR is a JVC VCR.

1Slide the remote control mode selector to ”DVD.”

2Press and hold VCR .

Keep it pressed until step 4 is finished.

3Press VCR CONTROL.

4Press Number buttons (1-9, 0) to enter a manufacturer’s code (2 digit).

See the list below to find the code.

Examples: For a Philips VCR, press 0, then 5.

For a Panasonic VCR, press 2, then 1.

5 Release VCR

TV VOL	CHANNEL	VOLUME
	TV/VIDEO MUTING
1		¡
/REW	PLAY	FF/

DOWN TUNING UP

REC	STOP	PAUSE
MEMORY		STROBE

DIMMER

CHANNEL +/– buttons

¡button

1 button

PLAY button

PAUSE button STOP button

÷REC button

6 Try to operate your VCR by pressing VCR		.

When your VCR turns on or off, you have entered the correct code.

If there are more than one cord listed for your brand of VCR, try each one

until you enter the correct one.

7To operate your VCR

You can use the following buttons for operating your VCR:

VCR :Turns on and off the VCR.

RM–STHV70R

DVD CINEMA SYSTEM

Manufacturers’ codes for VCR

•After pressing VCR CONTROL, you can use the following buttons for operating your VCR:

PLAY:	Starts playback.
STOP:	Stops operation.
PAUSE:	Pauses playback.
¡:	Fast forwards a video tape.
1:	Rewinds a video tape.

÷REC:Press this button together with PLAY to start recording.

Press this button together with PAUSE to pause recording.

CHANNEL +/–: Changes the TV channels on the VCR.

Manufacturer	Code	Manufacturer	Code
JVC	01	Nokia	16
Aiwa	02, 20	Nordmende	17	– 19, 31	* Manufacturers’ codes
Bell+Howell	03, 16	Orion	20		* Manufacturers’ codes
					are subject to change
Blaupunkt	04	Panasonic	21		are subject to change
					without notice. If they
CGM	03, 05, 16	Philips	05, 22		without notice. If they
					are changed, this
Daewoo	34	Phonola	05		are changed, this
					remote control cannot
Digtal	05	Saba	17	– 19, 23, 31	remote control cannot
					operate the
Fisher	03, 16	Samsung	24, 25		operate the
					equipment.
G.E.	06	Sanyo	03, 16		equipment.
Grundig	07	Sharp	26, 27
Hitachi	08, 09	Siemens	07
Loewe	05, 10, 11	Sony	28	– 30, 35
Magnavox	04, 05	Telefunken	17	– 19, 31, 32
Mitsubishi	12 – 15	Toshiba	33