For proper drying performanct

42-318

L107.6

:m)

-*=__-.

Explosion Hazard

Keep flammable materials and vapors away from dryer.

Place dryer at least 18 inches above the floor for a garage installation.

Failure to do so can result in death, explosion, fire, or burns.

The location must provide:

Protection from weather and water: Do not store or use dryer where it will be exposed to water and weather.

L/Room temperature above 45°F (7.2”C): If room

temperature is below 45°F (7.2” C), automatic

Icvcles mav not shut off.

Id’ Level floor:’ Maximum slope under entire dryer should not be more than i inch (2.5 cm). (Ii slope is greater than 1’ (2.5 cm), install Extended Dryer Feet Kit, Part No. 279810.) Clothes may not tumble properly and automatic sensor cycles may not operate correctly if dryer is not level.

/Sturdy floor to support dryer weight of 150 pounds (68 kg).

’(/Exhaust to outdoors: To prevent large amounts of

lint and moisture from accumulating and to maintain drying efficiency, exhaust dryer to outdoors.

1	“=x I
dryer exhaust	vent y

*from floor

with dryer feet

extended 1 \v inch (2.5 cm)

It is your responsibility to:

L/observe

all

governing

codes

and

ordinances.

(/consider

spacing

requirements

for companion

C/check

code

requirements:

Some codes limit

appliances.

do not

permit

installation

clothes

dryers

L/properly

install

dryer.

garages,

closets,

mobile

homes or

sleeping

C/m&e

sure

you

have

evm-vthinn

na~nccxrw

fnr

quarters.

Contact

your

local

building

inspector.

proper

installation.

with

the

installation

specifications

and

Ycomply

(/contact

qualified

installer

insure that the

dimensions.

electrical

installation

meets

all

national

and local

codes

and

ordinances.

Recessedarea/closet installation

Closet/confined area installation

If a closet door is installed: The

minimum unobstructed air openings are required. Louvered doors with equivalent air openings are acceptable.

Recessed area installation

The dryer should be exhausted to the outside for best performance.

If dryer is not exhausted outside, you must install Exhaust Deflector Kit. Part No. 3391278. available from your dealer.

klre Hazard

Exhaust dryer outside if installed in a closet. Use Exhaust Deflector Kit #3391278 if installed in a recessed area.

Failure to follow this instruction could result in a fire.

NOTE: No fuel-burning appliances may be installed in the same closet as a dryer.

l If codes permit, dryer may be installed in a

recessed area or closet using dimensions shown.

*Dimensions are in inches and are the minimum allowable.

l Additional spacing should be considered for ease of installation and servicing. Companion appliance spacing should also be considered,

front view

side view

3’ (7.6 cm)

,:;.,il F=-

**Minimum top and bottom air openings for closet door.

***External exhaust elbow requires additional space.

front view

l *** Wall .door and floor molding may require addItIonal spacing.

Door clearance

Location must be large enough to fully open dryer door.

3-710”(9.8 cm)

Electrlcal Shock Hazard

Electrical ground (earth) is required on this dryer.

Do Not ground (earth)to a gas pipe.

Do Not change the power supply cord plug. lf it does not fit the outlet, have a proper outlet installed by a qualified electrician.

Do Not have a fuse in the neutral or grounding circuit.

Do Not use an extension cord with this J dryer.

Do Not reuse old power supply cord.

Check with a qualified electrician to be sure dryer is properly grounded (earthed).

Do Not connect plug end of power supply cord into a live receptacle before connecting power supply cord to dryer terminal block.

Failure to follow these instructions could result in death or serious injury.

Important: Observe all governing codes and ordinances.

A two-wire, single phase, 220-volt, 60-Hz, AC-only, electrical supply is required on a separate 30-ampere circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended.

THE DRYER MUST BE CONNECTED WITH COPPER WIRE ONLY.

The dryer may be connected directly to the fused disconnect or circuit breaker box through

If codes permit and a separate grounding (earthing)

electrician determine that the grounding (earthing)

flexible, armored or non-metallic sheathed copper cable. Allow two or three feet

(61-91 cm) of slack in the line between the wall and the dryer so that it can be moved if servicing is ever necessary. A conduit connector must be provided at each end of the power supply cable (at the appliance and at the junction box). Wire sizes (COPPER WIRE ONLY)

and connections must conform with the rating of the appliance (30 amperes).

wire is used, it is recommended that a qualified path is adequate.

Grounding (earthing) instructions

This appliance must be connected to a grounded (earthed) metal, permanent wiring

system; or an equipment-grounding (earthing conductor must be run with the circuit conductors and connected to the equipment-

grounding (earthing) terminal or lead on the appliance.

Panel A

4LEC7646EN0 specifications

The Whirlpool 4LEC7646EN0 is a high-efficiency laundry appliance designed to accommodate various laundry needs while ensuring optimal performance and reliability. This model stands out for its combination of innovative features, user-friendly design, and energy-efficient technologies that make it a popular choice for households looking to simplify their laundry routines.

One of the key features of the Whirlpool 4LEC7646EN0 is its impressive capacity. With ample space for large loads, this appliance helps reduce the frequency of laundry sessions, allowing users to save both time and energy. Its ability to accommodate bulky items like bedding and towels adds to its versatility, making it suitable for families of all sizes.

The model utilizes advanced washing technologies that promote effective cleaning while being gentle on fabrics. The Adaptive Wash technology is particularly noteworthy, as it automatically senses the size and soil level of each load to adjust water levels and wash actions accordingly. This ensures that clothes are cleaned thoroughly without excessive wear and tear, extending their lifespan.

Another standout characteristic is the EcoBoost option, which optimizes energy use during the wash cycle. By adjusting the energy and water consumption, the EcoBoost feature allows users to achieve an efficient clean while minimizing their environmental impact. This aligns well with the growing trend of sustainable living and energy conservation.

In terms of convenience, the Whirlpool 4LEC7646EN0 offers a variety of customizable wash cycle options, allowing users to tailor their laundry experience based on fabric types and soil levels. The user-friendly control panel is designed for ease of operation, featuring intuitive settings that make selecting the appropriate cycle a breeze.

Additionally, the model is equipped with a Quiet Wash Noise Reduction System. This technology minimizes operational noise, ensuring that laundry can be done without disturbing the household. This feature adds to its appeal, particularly in homes where space is shared.

Overall, the Whirlpool 4LEC7646EN0 is a robust and efficient laundry solution. Its combination of innovation, user-friendly features, and energy-efficient technologies make it an excellent choice for those seeking to enhance their laundry experience while prioritizing garment care and sustainability. Whether dealing with everyday wear or larger items, this model proves to be a reliable partner for all laundry needs.