Whirlpool DRYERS warranty Using dryer fabric softeners, Saving energy, Vacation care

Page 26

TInted,

dyed or

Dry according

to fabric, weight and care label instructions. Wipe the dryer

non-colorfast

drum carefully

to remove any dye or lint that can

be transferred

to other

Items

 

loads. See “Cleaning the dryer

interior” on page

19.

 

Towels

 

Select cycle according to fabric

type. Some towels, particularly

those

 

 

made of a blend of synthetic fibers and natural fibers (polyester and

 

 

cotton blends), may shed more lint than other towels causing your dryer’s

 

 

lint screen to get full faster. Be sure to remove lint from the dryer lint

 

 

screen before and after drying new towels.

 

 

Washable

knlts

Do not overdry

knits. Overdrying

can cause shrinking and static

cling.

1.Select cycle according to fabric and construction.

2.Turn synthetics and blends inside out when drying to avoid pilling.

3.Remove cotton and rayon knits while still slightly damp. Stretch into shape and lay flat to finish drying.

Using dryer fabric softeners

Dryer fabric softeners are recommended for reducing static cling (static can also be re- duced by not overdrying) and for softening fabrics. Always follow package instructions carefully.

lPut fabric softener sheet on top of the load before startlng the dryer. Do not add a fabric softener sheet after the cycle has started. Instant heat can cause the fabric softener to spot fabrics.

l

l

Clear, grease-like spots can result from the fabric softener sheet becoming tangled in an item during tumbling. If fabric softener causes a stain, wet the stain and rub with liquid detergent or bar soap, rewash.

Some fabric softeners can clog the lint screen and slow drying. Use fabric softeners labeled as dryer safe.

Saving energy

l

l

l

Dry only full loads without overdrying.

Avoid overloading dryer, adding wet items to a partly dried load, or opening the door unnecessarily.

Plan your laundry to dry one load after another. A warm dryer shortens drying time.

l Shorten drying times by exhausting dryer properly and cleaning exhaust duct as needed.

-Keep the lint screen clean.

-Use your dryer in a room where room air temperature is above 45°F (7°C).

-Sort loads by fabric weight and type.

Vacation care

1.Unplug power supply cord or turn off electrical power supply.

2.Clean lint screen.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Understanding Safety Automatic DryersYour safety is important to us Thank you for buying a Whirlpool applianceUnderstanding Safety What to do if YOU Smell GASImportant SAFEl-Y Instructions Understanding your responsibilitiesKnowing Your Dryer’s Features Other doorsStarting or stopping your dryer Operating Your DryerBefore starting your dryer Selecting a cycle Push the Start Button, if necessaryUsing the automatic cycles Type of Load Using the Air cycle no heatUsing the Timed Drying cycle AIRUnderstanding Finish GUARD@ cycle Using the Tumble PRESW’ cycleUsing the Damp Dry cycle Using end of cycle signal Finish GUARD’ cycle selector LOW Heat Cycle control knob with 3 temperature settingsHigh Heat Permanent PRESS, Synthetics and BlendsLOW Cycle control knob and a temperature selector 2 settingsDelicate Fabrics Knits LinensMED Automatic Cycle High MED LOW EX LOW Cycle co&l Knob Temperature Tor End oicyck Drying rack suggestions Using the drying rackTemperature Time Rack DRYLint signal Maintenance-every loadCleaning the lint screen Caring For Your DryerCleaning the dryer interior Maintenance-as neededCleaning a clogged lint screen Cleaning the dryer exteriorChanging the drum light Electrlcal Shock and Fire HazardRemoving accumulated lint Drum seal Drying tips Laundry Tips Before you dry SortingDrying special-care items Diapers, baby clothes Elastic Items Vacation care Using dryer fabric softenersSaving energy CAUSES/SOLUTIONS Solving laundering problemsProblem Problem Check if Before calling for assistance If You Need Assistance Or ServiceSolution If you need assistance If you need serviceIf you are not satisfied with how the problem was solved If you need FSP replace- ment partsPage Whirlpool will not PAY for Length of WarrantyWhirlpool will PAY for
Top Page Image Contents