Vent Length Chart
Number of | Type of vent | Box or | Angled |
90º turns |
| louvered | hoods |
or elbows |
| hoods |
|
|
|
|
|
0 | Rigid metal | 90 ft (27.4 m) | 80 ft (24.4 m) |
| Flexible metal | 64 ft (19.5 m) | 58 ft (17.7 m) |
|
|
|
|
1 | Rigid metal | 80 ft (24.4 m) | 70 ft (21.3 m) |
| Flexible metal | 58 ft (17.7 m) | 52 ft (15.8 m) |
|
|
|
|
2 | Rigid metal | 70 ft (21.3 m) | 60 ft (18.3 m) |
| Flexible metal | 50 ft (15.2 m) | 42 ft (12.8 m) |
Install VentSystem
1.Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood.
2.Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.
3.Run vent to dryer location. Use the straightest path possible. See “Determine vent length.” Avoid 90º turns. Use clamps to seal all joints. Do not use duct tape, screws or other fastening devices that extend into the interior of the vent to secure vent.
LevelDryer
Check the levelness of the dryer. Check levelness first side to side, then front to back.
If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness.
NOTE: It might be necessary to level the dryer again after it has been moved into its final position.
ConnectVent
1.Using the coupling supplied with the dryer, connect the exhaust vent to the coupling and secure with a 4" (10.2 cm) vent clamp. See Illustration below.
AB C D E
A.Coupling
B.Vent clamp
C.Vent coupler
D.Vent clamp
E.Rigid or flexible metal vent
If connecting to existing vent, make sure the vent is clean.
2.Turn the coupling and exhaust vent assembly counterclockwise in the exhaust hole on the back of the dryer.
3.Make sure the exhaust vent is placed inside the exhaust hood and then secured to the exhaust hood with a 4" (10.2 cm) vent clamp.
WARNING
Excessive Weight Hazard
Use two or more people to move and install dryer. Failure to do so can result in back or other injury.
4.Move dryer into final position. Do not crush or kink vent. Make sure dryer is level.
CompleteInstallation
1.Check to be sure all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.
2.Check to be sure you have all of your tools.
3.Dispose of/recycle all packaging materials.
4.Check the dryer’s final location. Be sure the vent is not crushed or kinked.
5.Check to be sure the dryer is level. See “Level Dryer.”
6.Plug into a grounded outlet. Turn on power.
7.Remove the clear protective film on the front edge and any tape remaining on the dryer.
8.Read “Dryer Use.”
9.Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.
10.Set the dryer on a full heat cycle (not an air cycle) for 20 minutes and start the dryer.
If the dryer will not start, check the following:
■Controls are set in a running or “On” position.
■Start button has been pushed firmly.
■Dryer is plugged into a grounded outlet.
■Electrical supply is connected.
■House fuse is intact and tight, or circuit breaker has not tripped.
■Dryer door is closed.
11.When the dryer has been running for 5 minutes, open the dryer door and feel for heat.
If you do not feel heat, turn off the dryer and check the following:
■There may be 2 fuses or circuit breakers for the dryer. Check to make sure both fuses are intact and tight, or that both circuit breakers have not tripped. If there is still no heat, contact a qualified technician.
NOTE: You may notice a burning odor when the dryer is first heated. This odor is common when the heating element is first used. The odor will go away.
12