JVC GVT0155-001A manual Speaker layout, Connecting a TV, Connecting the power cord

Page 14

Connections

Speaker layout

	Center speaker
Front left			Front right
speaker			speaker

Subwoofer

Surround left	Surround right
speaker	speaker

• Place the satellite speakers on a flat and level surface.

•The front and center speakers are magnetically shielded to avoid color distortions on TVs. However, if not installed properly, they may cause color distortions. So, pay attention to the following when installing the speakers.

–When placing the speakers near a TV set, turn off the TV’s main power switch or unplug it before installing the speakers. Then wait

at least 30 minutes before turning on the TV’s main power switch again.

Some TVs may still be affected even though you have followed the above. If this happens, move the speakers away from the TV.

•The surround speakers and the subwoofer are not magnetically shielded.

If it is located nearby the TV or monitor, it will probably cause color distortion on the screen. To avoid this, do not place the speaker nearby the TV or monitor.

•Be sure to place the subwoofer to the TV’s right. If you place the subwoofer to the TV’s left, keep sufficient distance between them to prevent the TV screen from appearing mottled.

Connecting a TV

•Distortion of picture may occur when connecting the TV via a VCR, or to a TV with a built-in VCR.

•You need to set “MONITOR TYPE” in the PICTURE menu correctly according to the aspect ratio of your TV. (See page 32.)

Center unit

TV

To SCART connector

*Some TV’s SCART connectors output audiosignal. In such a case, you can enjoy the TV sound through this system.SCART cable (not supplied)

NOTE

•No sound signal comes out from “AV” (SCART) connector.

•Select the appropriate video signal according to your TV. (See page 15.)

Connecting the power cord

Make sure that all other connections have been completed.

Center unit

Power cord

Plug into AC outlets.

CAUTION

•Disconnect the power cord before cleaning or moving the system.

•Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp and pull the plug so as not to damage the cord.

NOTE

•Preset settings, such as preset stations and surround mode adjustment, may be erased in a few days in the following cases;

•If you unplug the power cord of the center unit.

•If a power failure occurs.

Image 14

Contents DVD Digital Cinema System GVT0155-001A BImportant for Laser Products Front view Side view Above ALLTable of contents Introduction Supplied accessoriesSafety precautions Important cautionsDiscs you can play About discsPlayable disc types Region code of DVD VideoFor all playable files Rear panel center unit Index of parts and controlsFront panel center unit Display windowIndex of parts and controls Remote controlOperating the system from the remote control R6P SUM-3/AA 15F type dry-cell batteries suppliedAM MW antennas Connecting the FMConnections AM MW loop antennaFront speakers Base plates Before assemblingPrepare a Phillips screwdriver not supplied Base plate Screw M4 x 40 mm supplied Speaker bottomInsulation coat off Connecting speakers for TH-S33Twist and pull Front speakersSpeaker cord Connecting speakers for TH-S11Connect the black cords to the black terminals Speaker layout Connecting a TVConnecting the power cord Make sure that all other connections have been completedOperating the TV To operate a JVC’s TVPress STANDBY/ON Basic operationsTurning the system on/off PressAdjusting the brightness of the indications Dimmer Adjusting the volume VolumeListening with headphones not supplied Selecting the source to playChanging the video signal Sleep Timer SleepAdjusting the sound Press 0 on the center unit PlaybackBasic Playback Place a discMP3 file Playback information on the display windowDVD VR disc Jpeg fileSkip to the beginning of a desired selection One Touch ReplayFast-forward/fast-reverse search Press TITLE/GROUP Locating a desired title/ group using number buttonsAbout the play mode on a DVD VR disc Press TOP MENU/PG or MENU/PLAdvanced operations Using the surround modeAvailable Surround modes for each input signal Auto Surround Auto SurrPress Surround repeatedly to select the desired mode Using the on-screen barSelecting the surround mode Showing the on-screen barPress on Screen twice Contents of the on-screen bar during playbackChanging the time information Playing from a specified position on a disc Locating a desired scene using a VCD/ Svcd menu with PBCLocating a desired chapter using the on- screen bar Locating a desired scene from the DVD menuLocating a desired position by specifying the time Using the file control displayTo cancel a misentry Beginning of current title/trackSelecting a view angle Resume PlaybackSelecting the subtitle Selecting the audio Frame-by-frame playback Changing the VFP settingSpecial picture playback Playing back in slow-motionProgram Playback Random PlaybackRepeating the current selection Repeating a desired part A-B RepeatTray lock SETTING, with Shift pressedPress Cursor To make an Adjustment or selection On Screen twiceMenu description Setting DVD preferencesUsing the setup menus Audio menu Audio Speaker setting menuPicture menu Picture Other setting menu Others You can activate or deactivate Resume Playback functionTuner operations Manual tuningPreset tuning Press FM Mode Selecting the FM reception modeUsing the RDS Radio Data System when receiving FM stations Press RDS/FL Display while listening to an FM stationPress PTY Search again To search for a program using the PTY codesPress PTY Search while listening to an FM station To continue searching after the first stopHow the Enhanced Other Network function actually works Switching to broadcast program of your choice temporarilyProgram type indicator Traffic Announcement in your areaTo clean the disc TroubleshootingCleaning the system ReferencesSpecifications Victor Company of Japan, Limited