Sunbeam 4215-099, 4211-099 instruction manual Using the IRON’S Special Features

Page 3

TO FILL THE WATER RESERVOIR

1.Make sure the iron is unplugged. Set the Steam Lever to O/Off (Dry) and the Fabric Select Dial to OFF.

2.Lift the Water Fill Hole Cover.

3.Fill water cup with water. Pour water into iron water reservoir. Do not fill water reservoir beyond maximum fill level.

WARNING: To prevent the risk of burns, be careful when filling a hot iron with water. Hot metal parts, hot water and steam can cause injuries.

DRY IRONING

1.Make sure the Steam Lever is turned to the O/Off (Dry) setting.

2.Plug the cord into a 120-Volt AC outlet.

3.Turn the large Fabric Select Dial to the fabric setting you desire (Silk or Synthetics). Allow the iron to heat for 2 minutes. While the iron is heating, make sure it is sitting on its heel rest on a stable, protected surface.

NOTE: While the Steam Lever is turned to the O/Off (Dry) setting, you may still use the SHOT OF STEAM® or SPRAY MIST® feature. Please make sure the water reservoir is 1/4 full of water.

TIP: Refer to the Ironing Guide (on Page 8) for the recommended setting for your fabric.

STEAM IRONING

1.Follow the instructions for “Filling the Water Reservoir”.

2.Plug the cord into a 120-Volt AC outlet.

3.Turn the large Fabric Select Dial to the fabric setting you desire (Synthetic, Silk, Linen, Cotton or Wool). Allow the iron to heat for 2 minutes. While the iron is heating, make sure it is sitting on its heel rest on a stable, protected surface.

4.Allow the iron to heat for 2 minutes, and then turn the Steam lever to the appropriate setting.

TIP: Refer to the Ironing Guide (on Page 8) for the recommended setting for your fabric.

IMPORTANT: When not ironing, always set the Steam Lever to O/Off (Dry) and the Fabric Select Dial to OFF.

USING THE IRONS SPECIAL FEATURES

SPRAY MIST® FEATURE

The SPRAY MIST® feature is a powerful water spray mist that dampens the fabric to aid in removing wrinkles from heavy fabrics and for setting creases.

To use the SPRAY MIST® Feature:

Press the SPRAY MIST® button firmly.

SHOT OF STEAM® FEATURE

The SHOT OF STEAM® feature provides an extra burst of steam for deep penetration of stubborn wrinkles. You can use this feature while Dry or Steam ironing, but the water reservoir must be at least 1/4 full of water.

To use the SHOT OF STEAM® Feature:

Place the iron on top of the wrinkle and press the SHOT OF STEAM® button each time you would like an extra burst of steam. The SHOT OF STEAM® feature may be used continuously with just a short pause between shots.

VERTICAL STEAM (Select Models Only)

The vertical steam feature allows your iron to function as a garment steamer.

TIP: When using the vertical steam on clothing, hang the clothing on a clothes hanger for best results. Hanging curtains and drapes may also be steamed.

To use Vertical Steam:

1.Make sure that the iron has heated up (2 minutes).

2.Hold the iron in a vertical position, with the iron close to but not touching the fabric you want to steam.

3.With your other hand, pull the fabric tight.

4.Press the SHOT OF STEAM® button for approximately 3-second intervals as you move the iron across the wrinkled area.

WARNING: To prevent the risk of burns, keep your hand away from the area being steamed.

WARNING: DO NOT steam garments while wearing them; this may result in injuries.

PATENTED MOTION SMART® AUTO-OFF FEATURE

When the iron is plugged in, the Power Indicator will light steadily, indicating that there is power to the iron.

If you leave the iron:

in a horizontal position without moving it, or accidentally tip the iron over, it will automatically stop heating after 30 seconds. The Power Indicator will blink to let you know that the iron has stopped heating.

in a vertical position (on its heel rest) without moving it, the iron will automatically turn off after 15 minutes. The Power Indicator will blink to let you know that the iron has stopped heating.

IMPORTANT: The Power Indicator will continue to blink until the iron is unplugged or reset.

To reset the iron:

Move the iron back and forth and allow it to reheat for 2 minutes. The indicator will stop blinking and the iron will start heating again.

WARNING: The patented MOTION SMART® Auto-Off is a safety feature, not a recommended means for turning your iron off. See “Caring for Your Iron After Use” (on Page 6) for information on turning off your iron and storing it safely between use.

ANTI-CALCIUMSYSTEM (Select Models Only)

The Anti-Calcium System is a permanent system located inside the water reservoir.

This system removes calcium from the water and reduces calcium build-up on the soleplate.

4

5

Image 3 Sunbeam 4215-099, 4211-099 instruction manual Using the IRON’S Special Features
Contents Manual de Instruçôes Ferros de Passar Steam Master Important Safeguards Using the IRON’S Special Features Ironing Tips Ironing Guide Précautions Importantes Caractéristiques DE Votre FER À Repasser Steam Master Entretien DE Votre FER À Repasser Steam Master Guida DE Repassage Contactez votre distributeur agrée de Sunbeam Precauciones Importantes USO DE LAS Funciones Especiales DE LA Plancha Recomendaciones Para EL Planchado Guía DE Planchado Precauções Importantes Usando AS Opções Especias do Ferro DE Passar Cuidados Para SEU Ferro DE Passar Depois DE Usado Modo DE Passar a Ferro Garantia Limitada DA Hospitalidade 2 Anos