Smeg KTL6 manual Consumption Data

Page 21

CONSUMPTION DATA

 

Temperature

Load

Water

Energy

Approx. Programme

Programme

 

 

 

 

Duration

 

(°C)

(kg)

(l)

(kWh)

(hours : minutes)

Cotton

95

5.0

50*

1.70

2:05

Cotton**

60

5.0

49

0.95

2:10

Cotton

40

5.0

55

0.55

2:00

Synthetics

60

2.5

50*

0.80

1:30

Synthetics

40

2.5

45

0.45

1:15

Delicates

40

1.5

50

0.55

0:45

Daily load

40

3.0

40

0.45

1:00

Quick wash

30

3.0

35

0.40

0:30

Wool

40

1.0

55

0.55

0:45

Handwash

40

1.0

40

0.40

0:35

Handwash

30

1.0

40

0.30

0:31

Prewash cycle increases programme duration by aproximately 20 min. Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

*To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

** Reference Programme for Energy Label.

START DELAY

The “Start delay” button allows the user to run the machine at his convenience, for example at night when electricity is cheaper.

Select programme, spin speed and options.

Press the “Start Delay” button several times to select a delay time of 1, 3, 6, 9 or 12 hours. The corresponding indicator lamp lights up.

Start the programme (see “Progremme Start”). The indication next to the “Start delay” button lights up and goes off when the programme starts.

Once having pressed the “Start/Pause” button, the countdown of the time delay begins. When the programme starts, the start delay indicator light goes off and is replaced by the programme sequence indication.

After the “Start/Pause” button has been pressed, the number of hours preselected can be reduced by pressing again the “Start delay” button.

To cancel the “Start delay”

..before you press the “Start/Pause” button:

Turn the programme selector to another position or press the “Reset” button.

RED INDICATIONS “Service”

Lighting up of the “Service” indication can be caused by a fault in an electrical component. Refer to the “Troubleshooting Guide” in your “Instructions for Use”; if the fault persists, contact our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open the water tap: if the indications still lights up, refer to the “Troubleshooting Guide” in the Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the drain hose is kinked or the filter must be cleaned: in the latter case refer to the Instructions for Use (“Removing the Filter”).

PROGRAMME END

All the lights of the programme sequence indicator are off, and the “Door open” indication lights up.

1.

Turn the programme selector to the “Off/O”

 

position.

2.

Close the water tap.

PREPARATION OF THE WASH CYCLE

1.Load the machine, close the drum doors and check that they are properly locked.

2.Add detergent and additives into the dispenser to no more than the “MAX” level mark, as follows:

Programme with pre and main wash

Main wash programme without prewash

Fabric softeners and conditioners

Stain remover agents

Anti-scale agents (if necessary)

3. Close the lid.

4. Turn the programme selector to the desired programme and temperature. The lamp next to the “Start/Pause” button flashes. The indication lamp of thepredefined spin speed lights up.

SELECT THE DESIRED OPTION(S)

Selecting or deselecting an option can be done at any time during the programme. The option will be applied as long as the corresponding programme phase has not been executed yet.

“Prewash” button

Only for heavily soiled loads (for example sand, granular dirt) sensible. Increases the cycle time by approximately 20 min.

“Cold wash” button

Water is heated only up to 20°C.

Suitable for delicate laundry items with wash temperature recommendation of max. 30°C on the care label.

Selectable only on the lowest temperature step of each programme.

“Variable spin” button

Every programme has a predefined spin speed.

Press the button to set another spin speed.

If spin speed “0” is selected, the final spinning is cancelled but intermediate spin peaks remain during the rinse. The water is drained out only.

..after having pressed the “Start/Pause” button:

Press the “Reset” button for at least 3 second. The start delay indicator light goes off.

PROGRAMME START

Open the tap and press the “Start/Pause” button. The indication lamp next to the “Start/Pause” button lights up. The programme sequence indicator shows the current programme phase, running from left to right through Wash, Rinse, Spin/Drain. When the programme phrase is finised, the corresponding indication goes out.

Note: If there is a power interruption or if the appliance is disconnected during the cycle, the programme will run again from the point where it was interrupted.

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the lamp lights to show the the lid can be opened. As long as a wash programme is running, the lid remains locked and must on no account be forced open. In case you have an urgent need to open it during a running programme, refer to “Cancel (Reset) a running programme before the end”.

3.

Open lid and drum and unload the machine.

4.

Leave the lid open for some time to allow the

 

interior of the machine to dry.

CHANGE PROGRAMME AND/OR OPTIONS AFTER PROGRAMME START

1.Press the “Start/Pause” button to pause the programme. The light flashes.

2.Select the new programme, any options and another spin speed if you want.

3.Press the “Start/Pause” button again. The new programme continues at the same position where the previous programme was interrupted. Do not add detergent for this programme.

CANCEL (RESET) A RUNNING PROGRAMME BEFORE THE END

The “Reset” button cancels a programme before the end. Press the “Reset” button for at least 3 seconds. Any existing water is drained out before the lid can be opened.

Image 21 Contents
Contents Before Using the Washing Machine Precautions and General Recommendations Adjustable feet Description of the Washing MachineBefore the First Wash Cycle Sort the laundry Preparation of the WashingStain removal Dyeing and bleachingLoading the laundry Detergents and Additives Choice of the right detergents and additivesDosage Where to put detergents and additives Using chlorine bleachUsing starch powder Cleaning the FILTER/ Draining Residual Water Detergent dispenser Water inlet hose filterWater inlet hose Appliance interior Appliance exterior and control panelLid seal Water inlet hosesContains residues from Blocked see Care and Maintenance Problem Causes, Solutions, TipsSpin cycle Installation Animation appears during such update periodsRed indication lamp Description of red indicationsDescription Start/Pause light flashesIndication on Description Before contacting After-Sales Service SpecifyWait for the water to cool so as to avoid any accidents Removal of transport bracket Adjust the feet Connect the water inlet hoseMake sure there are no kinks in the hose Connect the water drain hose Water stop anti-flooding systemBrown Live L Earth symbolTo fit a new plug, proceed as follows Polarized Plugs e.g pin, 13 amp plug conforming to BS 1363AKTL Programme Chart Consumption Data