Blomberg 8629 wze40 Installation, Appropriate installation location, Connecting water supply

Page 3

2 Installation

Refer to the nearest Authorised Service Agent for installation of the product. To make the product ready for use, review the information in the user manual and make sure that the electricity, tap water supply and water drainage systems are appropriate before calling the Authorized Service Agent. If they are not, call a qualified technician and plumber to have any necessary arrangements carried out.

C Preparation of the location and electrical, tap water and waste water installations at the place of installation is under customer's responsibility.

B warning: Installation and electrical connections of the product must be carried out by the Authorized Service Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons.

A warning: Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products cause risks for your safety.

C Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or crushed while pushing the product into its place after installation or cleaning procedures.

2.1 Appropriate installation location

Place the machine on a rigid floor. Do not place it on a long pile rug or similar surfaces.

Total weight of the washing machine and the dryer -with full load- when they are placed on top of each other reaches to approx. 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying capacity!

Do not place the product on the power cable.

Do not install the product at places where temperature may fall below 0ºC.

Place the product at least 1 cm away from the edges of other furniture.

2.2 Removing packaging reinforcement

Tilt the machine backwards to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon.

2.3 Removing the transportation locks

A warning: Do not remove the transportation locks before taking out the packaging reinforcement.

A warning: Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be damaged.

1.Loosen all the bolts with a suitable spanner until they rotate freely (C).

3 / 48 EN

2.Remove transportation safety bolts by turning them gently.

3.Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel. (P)

C Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future.

C Never move the product without the transportation safety bolts properly fixed in place!

2.4 Connecting water supply

C The water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa). It is necessary to have 10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly. Attach a pressure reducing valve if water pressure is higher.

C If you are going to use the double water-inlet product as a single (cold) water-inlet unit, you must install the supplied stopper to the hot water valve before operating the product. (Applies for the products supplied with a blind stopper group.)

A warning: Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will get damaged or the product will switch to protection mode and will not operate.

A warning: Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.

1.Connect the special hoses supplied with the product to the water inlets on the product. Red hose (left) (max. 90

ºC) is for hot water inlet, blue hose (right) (max. 25 ºC) is for cold water inlet.

A warning: Ensure that the cold and hot water connections

are made correctly when installing the product. Otherwise, your laundry will come out hot at the end of the washing process and wear out.

2.Tighten all hose nuts by hand. Never use a tool when tightening the nuts.

Washing Machine / User’s Manual

Image 3
Contents Document Number 2820522856EN WMF 8629 WZE40Important instructions for safety and environment Removing packaging reinforcement InstallationAppropriate installation location Connecting water supplyConnection must comply with national regulations Connecting to the drainAdjusting the feet Electrical connectionPreparation Detergent Drawer Using detergent and softenerLoading the laundry Open the loading doorColours Dark colours Delicates Using limescale removerTips for efficient washing Do not use bleaching agent and detergent by mixing themPreparing the machine Display symbolsOperating the product Control panelWoollens Type of laundry Laundry content Selectable Max. laundryMain programmes SyntheticsAdditional programmes Selecting the spin speed Temperature selectionSmartCARE Self Clean Special programmesNo Spin Soiling level selection12 / 48 EN Appears on the displaySee the programme description for maximum load Programme and consumption tableTime display Auxiliary function selectionChanging the selections after programme has started End TimeStarting the programme Loading door lockEnd of programme Cancelling the programmeMemory Favourite program setting Child LockKeep the Favourite button pressed for 3 seconds Entering the Settings menuCountdown as Storing favourite 3-2-1 appears on the display To navigate in menus Changing the language selectionClean the detergent drawer at regular intervals every Maintenance and cleaningCleaning the detergent drawer Cleaning the loading door and the drumCleaning the body and control panel Cleaning the water intake filtersDraining remaining water and cleaning the pump filter 20 / 48 EN Install the filterTechnical specifications Troubleshooting Номер на документа 2820522856BG Информация за опаковъчните материали Обща безопасностПредназначение на уреда Безопасност на децатаМонтаж ПРЕДУПРЕЖДЕНИЕНе използвайте Свързване към отводнителната системаРегулиране на крачетата Свързване на електричествотоКакво да направите за да спестите енергия ПодготовкаСортиране на прането Подготовка на дрехите за пранеСпазване капацитета на прането Зареждане на пранетоУпотреба на перилен препарат и омекотител Използване на препарат за колосване Регулиране количеството на препаратаИзползване на омекотители Ако уредът не е оборудван с чашка за течен перилен препаратСъвети за ефективно изпиране Подготовка на машината Работа с уредаКонтролен панел Символи на дисплеяСинтетични тъкани Основни програми32 / 48 BG Памучни материи33 / 48 BG Допълнителни програмиЦентрофугиране + Помпа Специални програмиИзбор на температура Избиране на скорост на центрофугиранеФункция Без центрофугиране 10 Избор ниво на замърсеностБутон Регулиране на нивото на замърсеност 35 / 48 BG36 / 48 BG 11 Таблица с програми и консумация12 Избор на допълнителни функции 13 Препоръчителни количества пране и перилен препарат37 / 48 BG 38 / 48 BG Time Setting Настройка на крайния час14 Краен час 15 Стартиране на програмаДобавяне на пране след стартиране на програмата 16 Заключване на вратата17 Промяна на настройките след стартиране на програмата 18 Защита от децаСелетора на програмите огато машината е 19 Отказ на програма21 Настройка на Memory любима програма 22 Влизане в меню Настройки41 / 48 BG Промяна на настройката за яркост на екранаЗаглушаване и пускане на звука Почистване на корпуса и контролния панел Поддръжка и ПочистванеПочистване на чекмеджето за препарати Почистване на вратата и барабана43 / 48 BG За да почистите мръсния филтър и да източите водатаЗавъртете филтъра на помпата за да го извадите WMF 8629 WZE40 Технически спецификацииВъзможни решения на възникнали проблеми 46 / 48 BG 47 / 48 BG