Blomberg 8629 wze40 user manual Troubleshooting

Page 22

7 Troubleshooting

Programme cannot be started or selected.

Washing machine has switched to self protection mode due to a supply problem (line voltage, water pressure, etc.). >>> Press and hold Start / Pause button for 3 seconds to reset the machine to factory settings. (See "Cancelling the programme")

Water in the machine.

Some water might have remained in the product due to the quality control processes in the production. >>> This is not a failure; water is not harmful to the machine.

Machine vibrates or makes noise.

Machine might be standing unbalanced. >>> Adjust the feet to level the machine.

A hard substance might have entered into the pump filter. >>> Clean the pump filter.

Transportation safety bolts are not removed. >>> Remove the transportation safety bolts.

Laundry quantity in the machine might be too little. >>> Add more laundry to the machine.

Machine might be overloaded with laundry. >>> Take out some of the laundry from the machine or distribute the load by hand to balance it homogenously in the machine.

Machine might be leaning on a rigid item. >>> Make sure that the machine is not leaning on anything.

Machine stopped shortly after the programme started.

Machine might have stopped temporarily due to low voltage. >>> It will resume running when the voltage restores to the normal level.

Programme time does not countdown. (On models with display)

Timer may stop during water intake. >>> Timer indicator will not countdown until the machine takes in adequate amount of water. The machine will wait until there is sufficient amount of water to avoid poor washing results due to lack of water. Timer indicator will resume countdown after this.

Timer may stop during heating step. >>> Timer indicator will not countdown until the machine reaches the selected temperature.

Timer may stop during spinning step. >>> Automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the drum.

Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment. Laundry should be rearranged and re-spun.

Foam is overflowing from the detergent drawer.

Too much detergent is used. >>> Mix 1 tablespoonful softener and ½ l water and pour into the main wash compartment of the detergent drawer.

Put detergent into the machine suitable for the programmes and maximum loads indicated in the “Programme and consumption table”. When you use additional chemicals (stain removers, bleachs and etc), reduce the amount of detergent.

Laundry remains wet at the end of the programme

Excessive foam might have occurred and automatic foam absorption system might have been activated due to too much detergent usage.

>>> Use recommended amount of detergent.

Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment. Laundry should be rearranged and re-spun.

Awarning: If you cannot eliminate the problem although you follow the instructions in this section, consult your dealer or the Authorized Service Agent. Never try to repair a nonfunctional product yourself.

22 / 48 EN

Washing Machine / User’s Manual

 

 

Image 22
Contents WMF 8629 WZE40 Document Number 2820522856ENImportant instructions for safety and environment Connecting water supply InstallationAppropriate installation location Removing packaging reinforcementElectrical connection Connecting to the drainAdjusting the feet Connection must comply with national regulationsPreparation Open the loading door Using detergent and softenerLoading the laundry Detergent DrawerDo not use bleaching agent and detergent by mixing them Using limescale removerTips for efficient washing Colours Dark colours DelicatesControl panel Display symbolsOperating the product Preparing the machineSynthetics Type of laundry Laundry content Selectable Max. laundryMain programmes WoollensAdditional programmes Special programmes Temperature selectionSmartCARE Self Clean Selecting the spin speedAppears on the display Soiling level selection12 / 48 EN No SpinProgramme and consumption table See the programme description for maximum loadAuxiliary function selection Time displayLoading door lock End TimeStarting the programme Changing the selections after programme has startedChild Lock Cancelling the programmeMemory Favourite program setting End of programmeTo navigate in menus Changing the language selection Entering the Settings menuCountdown as Storing favourite 3-2-1 appears on the display Keep the Favourite button pressed for 3 secondsCleaning the loading door and the drum Maintenance and cleaningCleaning the detergent drawer Clean the detergent drawer at regular intervals everyCleaning the water intake filters Cleaning the body and control panelDraining remaining water and cleaning the pump filter Install the filter 20 / 48 ENTechnical specifications Troubleshooting Номер на документа 2820522856BG Безопасност на децата Обща безопасностПредназначение на уреда Информация за опаковъчните материалиМонтаж Свързване на електричеството Свързване към отводнителната системаРегулиране на крачетата ПРЕДУПРЕЖДЕНИЕНе използвайтеПодготовка на дрехите за пране ПодготовкаСортиране на прането Какво да направите за да спестите енергияЗареждане на прането Спазване капацитета на пранетоУпотреба на перилен препарат и омекотител Ако уредът не е оборудван с чашка за течен перилен препарат Регулиране количеството на препаратаИзползване на омекотители Използване на препарат за колосванеСъвети за ефективно изпиране Символи на дисплея Работа с уредаКонтролен панел Подготовка на машинатаПамучни материи Основни програми32 / 48 BG Синтетични тъканиДопълнителни програми 33 / 48 BGИзбиране на скорост на центрофугиране Специални програмиИзбор на температура Центрофугиране + Помпа35 / 48 BG 10 Избор ниво на замърсеностБутон Регулиране на нивото на замърсеност Функция Без центрофугиране11 Таблица с програми и консумация 36 / 48 BG13 Препоръчителни количества пране и перилен препарат 12 Избор на допълнителни функции37 / 48 BG 15 Стартиране на програма Time Setting Настройка на крайния час14 Краен час 38 / 48 BG18 Защита от деца 16 Заключване на вратата17 Промяна на настройките след стартиране на програмата Добавяне на пране след стартиране на програмата22 Влизане в меню Настройки 19 Отказ на програма21 Настройка на Memory любима програма Селетора на програмите огато машината еПромяна на настройката за яркост на екрана 41 / 48 BGЗаглушаване и пускане на звука Почистване на вратата и барабана Поддръжка и ПочистванеПочистване на чекмеджето за препарати Почистване на корпуса и контролния панелЗа да почистите мръсния филтър и да източите водата 43 / 48 BGЗавъртете филтъра на помпата за да го извадите Технически спецификации WMF 8629 WZE40Възможни решения на възникнали проблеми 46 / 48 BG 47 / 48 BG