John Lewis JLWD 1408 instruction manual Unpacking, Positioning, Remove the polystyrene base

Page 7

Unpacking

All transit bolts and packing must be removed before using the appliance.

You are advised to keep all transit devices so that the they can be refitted if the machine ever has to be transported again.

5.Set the machine upright and unscrew the remaining rear screw. Slide out the relevant pin.

6.Fill all the holes with the plastic plugs supplied with the instruction booklet.

P1129

P0001

Important !

You are advised to keep all the packaging for re- use in case the machine is to be transported again. In case of moving out the same

1.Using the supplied spanner unscrew and remove the two rear bottom screws. Slide out the two plastic pins. Lay the machine gently on its back, making sure that the hoses are not squashed.

precautions as per paragraph “The dangers of freezing” must be taken i.e. the residual water in the hoses must be pumped out.

1

2

3

P1124

P1126

Positioning

Install the machine on a flat hard floor.

Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Check that the machine does not touch the wall or other kitchen units.

Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor.

2.Remove the polystyrene block from the bottom of the machine and release the two plastic bags.

3.Very carefully slide out the left polythene bag, removing it towards the right and then downwards. Repeat the operation for the right polythene bag, removing it towards the left and then upwards.

P1127

4. Remove the polystyrene base.

Your new washer-dryer has been designed to be permanently plumbed in to your home’s water supply and drainage system. However, if this is not possible, it may be connected to a suitable existing tap with the drain hose discharging into a sink.

The appliance has an inlet hose, with female 3/4” BSP thread connector. If this connection is not compatible with the plumbing of the existing installation, a variety of connectors are available from good hardware stores and plumbers merchants to suit most domestic plumbing. Any alteration to your existing plumbing must be carried out by a competent person, or qualified plumber.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Jlwd Spin washer-dryer Child Safety InstallationUse Environmental Information Maintenance and CleaningService Ecological hintsContents Detergent dispenser drawer Child safety featureDescription of the Appliance Door locked lightDrying InstallationTechnical Specifications WashingPositioning UnpackingRemove the polystyrene base Appliance must be connected to a cold water supply Installation on a Suspended FloorWater inlet Water drainageOnto a sink outlet spigot LevellingSpecial conditions Interest of the environmentElectrical connection «E» or by the earth symbol or coloured green and yellowPermanent connection Spin speed Control panelDetergent dispenser drawer Programme selector dial Spin buttonTime dry button Delay start buttonOption buttons Automatic Dry buttonExample Start/Pause buttonDisplay Programme time Selection of drying time in minutesProgramme phase indicator lights Max. load 1.5 kg Final spin speed 900 r.p.m Programme informationSelect the spin speed or the Rinse hold option Switch the machine onLoad the laundry Measure out the detergentSelect the desired options How to change an option or a programme during its cycleSelect the Delay start How to interrupt a programmeRemove the laundry from the washer dryer End of programmeLeave the door ajar in order to air the machine Press the Start/Pause button to start the programme DryingSheet 1000g = 1 kgBath robe Important Notes Wash Care SymbolsWashing programmes Soak Off ResetProgramme Consumptions Energy Water Description KWhStore dry Drying ProgrammesDegree Type of fabric Max. load Spin speed Drying time Extra dryMaintenance and Cleaning Remove any objects from the pump impeller by rotating it Cleaning the water inlet filterScrew the pump cover fully Close the pump door Emergency emptying out Something Not Working Light has gone out Spinning starts late or Machine vibrates whenSpinning Door will not openAlways insist on genuine spare parts 0870 0103/07 132 973
Top Page Image Contents