Kenmore 9412*, 9400*, 9410*, 9411*, 790.9090*, 9091*, 9413* manual Before You Call, Possible

Page 20

Before You Call

Solutions to Common Problems

Before you carl for service, review this list. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance.

OCCURRENCE

POSSIBLE

CAUSE/SOLUTION

Range is not level.

Poor installation.

Place oven rack in center of oven. Place a level on the oven rack. Adjust

 

leveling legs at base of range until the oven rack is level.

Be sure floor is level and is strong and stable enough to adequately support range.

Cannot move appliance easily. Appliance must be accessible for service.

Oven control beeps and displays any F code error (for example Fll).

Surface element too hot or not hot enough.

Surface element does not heat.

If floor is sagging or sloping, contact a carpenter to correct the situation.

Kitchen cabinet alignment may make range appear unlevel. Be sure cabinets are square and have sufficient room for range clearance.

Cabinets not square or are built in too tightly. Contact builder or installer to make appliance accessible.

Carpet interferes with range. Provide sufficient space so range can be lifted over carpet.

Electronic control has detected a fault condition. Press STOP/C LEAR to clear the display and stop beeping. Reprogram oven. If fault recurs, record fault number. Press STOP/ CLEAR and call 1-800=4=MY=HOME® for assistance (See back cover).

Incorrect control setting. Make sure the correct control is on for the element to be used.

Lightweight or warped pans used. Use only flat, evenly balanced, medium or heavyweight cookware. Flat pans heat better than warped pans. Cookware materials and weight of the material affect heating. Heavy and medium-weight pans heat evenly. Because lightweight pans heat unevenly, foods may burn easily.

No power to the appliance. Check steps under "Entire Appliance Does Not Operate" in this Before You Call checklist.

Incorrect control setting. Make sure the correct control is set for the surface element to be used.

Entire appliance does not operate.

Make sure cord/plug

is plugged

correctly into outlet.

 

 

Service wiring is not

complete.

Call 1-800=4-MY-HOME®

for assistance (See back

 

cover).

 

 

 

Power outage. Check house lights to be sure. Call your local electric company for service.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Estufa elctrica Table of Contents Important Safety instructions InuseTheyshouldneverbeallowedtositorstandonanyIMPORTANT iNSTRUCTiONS for Using Your Important Safety NoticeU.S.A Master Protection AgreementsAcuerdos maestros de proteccibn Proteccibn contra picos de energia o dafiosYour Electric Range Features Include @ /i ¸¸Before Setting Oven Controls Element on indicator Lights Before Setting Oven Controls contdSetting Surface Controls Cookware Material Types Using proper cookwareSurface Cooking Temperature conversion Oven Control FunctionsSetting Oven Controls To Set the Minute TimerTo Change the Minute Timer while it is in use To Set the ClockSetting Oven Controls contd To Set or Change the Temperature for BakingTo Set Control for Continuous Bake or 12 Hour Energy Saving To Set Control for Oven Lockout LockoutTo Set for Broiling To Operate the Oven LightAdhere to the following cleaning precautions Self-CleaningSelf=Cleaning Oven Self-Cleaning contd Starting the Select Self=Clean CycleTo Set the Controls for a Self=Clean Cycle Stopping or Interrupting a Select Self=Cleaning CycleStainless Steel, Chrome Control Panel, Decorative Trim General Care & CleaningSurfaces How to Clean Lift-up General Care & Cleaning contdSurface Elements and Drip Bowls Removing and Replacing the Lift-OffOven Door Changing the Oven Light some models Adjusting the Oven TemperatureCare and Cleaning of Stainless Steel some models Before You Call PossibleOccurrence Possible CAUSE/SOLUTION Before You Call827 Call anytime, day or night U.S.A. and CanadaCallanytime, dayornight
Top Page Image Contents