LocationRequirements
Selecting the proper location for your washer improves performance and minimizes noise and possible washer “walk.”
Your washer can be installed in a basement, laundry room, closet, or recessed area. See “Drain System.”
IMPORTANT: Do not install or store the washer where it will be exposed to the weather.
Proper installation is your responsibility.
You will need:
■A water heater set to deliver 120°F (49°C) water to the washer.
■A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is attached to the back of the washer. See “Electrical Requirements.”
■Hot and cold water faucets located within 3 ft (90 cm) of the hot and cold water fill valves, and water pressure of
■A level floor with a maximum slope of 1" (2.5 cm) under entire washer. Installing the washer on carpeting is not recommended.
■A sturdy floor to support the washer weight (washer, water and load) of 315 lbs (143 kgs).
Do not store or operate your washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. See “Washer Care” in the Washer User Instructions for information on winterizing.
Recessed area or closet installation
The dimensions shown are for the recommended spacing allowed (A and B), except the closet door ventilation openings. The dimensions shown for the closet door ventilation openings (C) are the minimum required.
|
|
|
|
|
|
| 3" |
|
|
|
| 14" max. | 48 in.2 |
| (7.6 cm) |
|
|
|
|
|
| ||
19" |
|
|
| (35.6 cm) | (310 cm2 ) |
| |
|
|
|
|
|
|
| |
(48.3 cm) |
|
|
|
|
|
|
|
|
|
|
|
| 2 |
|
|
|
|
|
|
| 24 in. |
| 3" |
|
|
|
|
| (155 cm2 | ) | |
|
|
|
|
|
|
| (7.6 cm) |
0" | 27" | 0" | 1" | 25¹⁄₂" | 4" |
|
|
(0 cm) | (68.6 cm) | (0 cm) | (2.5 cm) | (64.8 cm) | (10.2 cm) |
| |
| A |
|
| B |
|
| C |
A. Front view
B. Side view
C. Closet door with vents
■Additional spacing should be considered for ease of installation and servicing.
■Additional clearances may be required for wall, door and floor moldings.
■Additional spacing of 1" (2.5 cm) on all sides of the washer is recommended to reduce noise transfer.
■If a closet door is installed, the minimum air openings in the top and bottom of the door are required (C). Louvered doors with air openings in the top and bottom are acceptable.
■Companion appliance spacing should also be considered.
DrainSystem
The washer can be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor drain system. Select the drain hose installation method you need. See “Tools and Parts.”
Standpipe drain system—wall or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe of 2" (5 cm). The minimum
The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (244 cm) from the bottom of the washer.
To avoid siphoning, no more than 8" (20.3 cm) of drain hose should be inside the standpipe. Secure drain hose with beaded tie strap.
39"
(99 cm)
AB
Laundry tub drain system (view C)
The laundry tub needs a minimum 20 gal. (76 L) capacity. The top of the laundry tub must be at least 39" (99 cm) above the floor and no higher than 96" (244 cm) from the bottom of the washer.
Floor drain system (view D)
The floor drain system requires a siphon break that may be purchased separately. See “Tools and Parts.”
The siphon break must be a minimum of 28" (71 cm) from the bottom of the washer. Additional hoses might be needed.
To avoid siphoning, no more than 8" (20.3 cm) of drain hose should be below the top of the wash tub. Secure drain hose with beaded tie strap.
39" | 28" |
(71 cm) |
(99 cm)
CD
3