Whirlpool W10150593A SecuretheDrainHose, Level theWasher, Check for leaks

Page 7

Connect the inlet hoses to the washer

A

B

A. Cold water inlet valve

B. Hot water inlet valve

1.Attach the hot water hose to the bottom inlet valve.

2.Attaching the hot water coupling first makes it easier to tighten connection with pliers.

3.Screw on coupling by hand until it is seated on the washer.

4.Using pliers, tighten the couplings with an additional two- thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.

5.Attach the cold water hose to the top inlet valve.

6.Screw on coupling by hand until it is seated on the washer.

7.Using pliers, tighten the couplings with an additional two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.

Check for leaks

Turn on the water faucets and check for leaks. A small amount of water might enter the washer. You will drain this later.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or replacement dates for future reference.

■If you connect only one water hose, you must cap off the remaining water inlet port.

■Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.

SecuretheDrainHose

1.Remove the shipping material from the power cord. Drape the power cord over the console.

2.Remove any cardboard used to move washer.

Beaded tie strap

3.Wrap the drain hose to the laundry tub leg, drain standpipe or inlet hoses, with the beaded tie strap. Push fastener into the nearest hole in the beaded tie strap. See view A or B.

ABC

If the washer faucets and the drain standpipe are recessed, put the formed end of the drain hose into the standpipe. Tightly wrap the tie strap around the water inlet hoses and the drain hose. See view C.

Level theWasher

Properly leveling your washer avoids excessive noise and vibration.

Install the Front Leveling Feet

1.Prop up the front of the washer about 4" (10.2 cm) with a wood block or similar object. The block needs to support the weight of the washer.

A

4"

(10.2 cm)

A. Threaded holes for feet

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Washer Safety Washer Installation InstructionsAlternate Parts Installation RequirementsTools andParts Parts suppliedDrainSystem LocationRequirementsYou will need RemoveShippingMaterials Installation InstructionsElectricalRequirements BeforeYouStartStraight power cord Looped power cord To keep drain water from going back into the washer Connecting the drain hose form to the corrugated drain hoseConnectDrainHose ConnecttheInletHosesCheck for leaks Install the Front Leveling FeetSecuretheDrainHose Level theWasherSteps in Final Location CompleteInstallationPièces fournies Exigences D’INSTALLATIONSécurité DE LA Laveuse OutillageetpiècesIl vous faudra Exigences d’emplacementSystèmedevidange Autres piècesÉvier de buanderie illustration C SpécificationsélectriquesSiphon de plancher illustration D Cordon dalimentation droit Instructions D’INSTALLATIONAvantdecommencer RetraitdumatérieldexpéditionRaccordementdes tuyauxd’arrivéed’eau RaccordementdutuyaudevidangePour empêcher l’eau de vidange de refluer dans la laveuse Raccorder les tuyaux d’arrivée d’eau à la laveuse ImmobilisationdutuyaudevidangePurger les canalisations d’eau Inspection-recherche des fuitesInstallation des pieds de nivellement avant Étapes dans lemplacement finalRéglagedel’aplombdelalaveuse W10150593A SP PN W10150594A Acheverl’installation
Top Page Image Contents