Whirlpool W10200828B, W10200829B-SP warranty Troubleshooting, Washer and Components

Page 6

TROUBLESHOOTING

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

to possibly avoid the cost of a service call.

In U.S.A. www.whirlpool.com In Canada www.whirlpool.ca

Washer and Components

Washer Operation

Noisy

Is the load balanced and the washer level? The wash load should be balanced and not overloaded. The washer must be level. The front feet should be properly installed and the nuts tightened. Reset the rear leveling legs (if needed). See the Installation Instructions.

Did you completely remove the yellow shipping strap with shipping pins? See the Installation Instructions.

Are the gears engaging after the drain and before spin, or is the upper part of agitator clicking during wash? These are normal washer noises.

Leaking

Check the following: Are the fill hoses tight?

Are the fill hose washers properly seated?

Is the drain hose clamp properly installed? See the Installation Instructions.

Is the sink or drain clogged? Sink and standpipe must be able to handle 17 gal. (64 L) of water per minute.

Is water deflecting off the tub ring or the load? Center the tub before starting the washer. The wash load should be balanced and not overloaded. The fill or spray rinses can deflect off the load. The washer must be level. The front feet should be properly installed and the nuts tightened. Reset the rear leveling legs (if needed). See the Installation Instructions.

Check household plumbing for leaks.

Basket crooked

Was the washer basket pulled forward during loading? Push the basket to the center before starting wash.

Is the load balanced and the washer level? The wash load should be balanced and not overloaded. The washer must be level. The front feet should be properly installed and the nuts tightened. Reset the rear leveling legs (if needed). See the Installation Instructions.

The washer basket moves while washing. This is normal.

Agitator operation

The top of the agitator is loose, or moves in only one direction. This is normal.

Dispensers clogged or bleach leaking

Did you follow the manufacturer’s directions when adding detergent and fabric softener to the dispensers (on some models)? Measure detergent and fabric softener. Slowly pour into the dispensers. Wipe up all spills. Dilute fabric softener in the fabric softener dispenser.

Did you put powdered or color-safe bleach into the liquid chlorine bleach dispenser (on some models)? Add powdered or liquid color-safe bleach directly to the basket. Do not use the chlorine bleach dispenser for color-safe bleach.

Washer won’t run, fill, rinse, or agitate; washer stops

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Is the power cord plugged into a grounded 3 prong outlet? Plug power cord into a grounded 3 prong outlet.

Are you using an extension cord? Do not use an extension cord.

Is the indicator on the Timer knob properly lined up with a cycle? Turn the Timer knob to the right slightly and pull to start.

Are the water inlet valve screens clogged? Turn off the water and remove inlet hoses from the washer. Remove any accumulated film or particles. Reinstall hoses, turn on water and check for leaks.

Are both the hot and cold water faucets turned on? Turn on the water.

Is the water inlet hose kinked? Straighten the hoses.

Does the water level seem too low, or does the washer appear to not fill completely? The top of the agitator is much higher than the highest water level. This is normal and necessary for clothes to move freely.

Has a household fuse blown, or has a circuit breaker tripped? Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician.

Is the washer in a normal pause in the cycle? The washer pauses for about 2 minutes during certain cycles. Allow the cycle to continue. Some cycles feature periods of agitation and soak.

Is the washer overloaded? Wash smaller loads.

Is the lid open? The lid must be closed during operation. Washer will not agitate or spin with the lid open.

Washer won’t drain or spin

Is the drain hose clogged, or the end of the drain hose more than 96" (2.4 m) above the floor? See the Installation Instructions for proper installation of drain hose.

6

Image 6
Contents Assistance or Service AccessoriesWasher Safety Your safety and the safety of others are very importantWasher USE StartingYourWasherCool brights/darks Wash Temp Suggested Fabrics HotWarm ColdWater Inlet Hoses Cleaning Your WasherWasher Care Moving and StorageTroubleshooting Washer and ComponentsWasher Results Residue or lint on loadStains on load To locate FSP replacement parts in your area This limited warranty does not coverCall 1­800­807­6777 Replacement parts CallPage Assistance ou service AccessoiresProduit numéro Accessoire Sécurité DE LA Laveuse Votre sécurité et celle des autres est très importanteUtilisation DE LA Laveuse MiseenmarchedelalaveuseTap Cold froide Arrêt ou remise en marche de la laveuseTuyaux darrivée deau Entretien DE LA LaveuseNettoyage de votre laveuse Préparation avant un entreposage ou un DéménagementDépannage La laveuse et ses composantsFonctionnement de la laveuse Résultats de lavage Page La présente garantie limitée ne couvre pas Pièces de rechangePour localiser des pièces de rechange FSP dans votre région Page W10200828B W10200829B-SP