Whirlpool W10112488 installation instructions Complete Installation, Steps in Final Location

Page 8

2.Screw the locknut onto each foot to within 1" (2.5 cm) of the foot base.

1"

(2.5 cm)

3.Screw the feet into the threaded holes at the front corner of the washer until the nuts touch the washer. Twist the feet to install.

NOTE: Do not tighten the nuts until the washer is level.

4.Tilt the washer back and remove the wood block. Gently lower the washer to the floor.

Steps in Final Location

1.Slide the washer to its final location.

2.Tilt the washer forward until the rear of the washer is at least 4" (10.2 cm) off the floor. You may hear the self-adjusting rear feet click into place. Lower the washer to the floor.

A

4"

(10.2 cm)

A.Self-adjusting feet

3.Check the levelness of the washer by placing a level on the top edges of the washer, first side to side, then front to back.

4.If the washer is not level, move the washer out slightly, tip back, prop up the front of the washer with the wood block and adjust the feet up or down as necessary by twisting the feet. Turn the feet clockwise to raise the washer or counterclockwise to lower the washer. Repeat steps

1through 4 until washer is level.

5.After the washer is in the final location and level, use a ⁹⁄₁₆" or

14mm open-end wrench to turn the nuts counterclockwise on the feet tightly against the washer cabinet.

IMPORTANT: If the nuts are not tight against the washer cabinet, the washer may vibrate.

Complete Installation

1.Check the electrical requirements. Be sure that you have the correct electrical supply and the recommended grounding method. See “Electrical Requirements.”

2.Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.

3.Check that you have all of your tools.

4.Check that the yellow shipping materials were completely removed from the lower back of the washer.

5.Dispose of/recycle all packaging materials.

6.Check that the water faucets are on.

7.Check for leaks around faucets and inlet hoses.

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

8.Plug into a grounded 3 prong outlet.

9.Remove the protective film on the console and any tape remaining on the washer.

10.Read “Washer Use” in the Washer User Instructions.

11.To test and to clean your washer, measure ¹⁄₂ of the normal recommended amount of powdered or liquid detergent and pour it into the washer basket or detergent dispenser (on some models). Close the lid. Select any cycle, and then pull the cycle control knob out to start the washer. Allow it to complete one whole cycle.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Washer Installation Instructions Washer SafetyInstallation Requirements Tools and PartsYou will need Location RequirementsDrain System Before You Start Installation InstructionsElectrical Requirements Looped power cord To remove the power cord from the cord restraint, pushStraight power cord Connecting the drain hose form to the corrugated drain hose Connect Drain HoseConnect the Inlet Hoses To keep drain water from going back into the washerInstall the Front Leveling Feet Secure the Drain HoseLevel the Washer Check for leaksSlide the washer to its final location Complete InstallationSteps in Final Location Seguridad DE LA Lavadora Requisitos DE InstalaciónHerramientas y piezas Piezas necesarias no están provistas con la lavadoraRequisitos de ubicación Sistema de desagüePiezas alternativas Usted necesitaráRequisitos eléctricos Sistema de desagüe en un lavadero vista CSistema de desagüe en el piso vista D Se requiere una fuente de alimentación eléctrica deInstrucciones DE Instalación Antes de empezarCómo quitar el material de transporte Cable de suministro de energía derechoCómo evitar que el agua del desagüe regrese a la lavadora Cómo conectar la manguera de desagüeConecte las mangueras de entrada Asegure la manguera de desagüe Limpie las tuberías del aguaRevise si hay pérdidas de agua Conecte las mangueras de entrada a la lavadoraNivele la lavadora Instale las patas niveladoras delanterasPasos en la ubicación final Deslice la lavadora hasta su ubicación finalSécurité DE LA Laveuse Complete la instalaciónExigences D’INSTALLATION Outillage et piècesIl vous faudra Exigences d’emplacementSystème de vidange Instructions D’INSTALLATION Spécifications électriquesAvant de commencer Retrait du matériel dexpéditionPour retirer le cordon dalimentation du dispositif Cordon d’alimentation droitLe sortir Cordon d’alimentation en boucleRaccordement du tuyau de vidange Raccordement des tuyaux d’arrivée d’eauPour empêcher l’eau de vidange de refluer dans la laveuse Purger les canalisations d’eauRaccorder les tuyaux d’arrivée d’eau à la laveuse Immobilisation du tuyau de vidangeInspection-recherche des fuites Réglage de l’aplomb de la laveuse Achever l’installation W10112488

W10112488 specifications

The Whirlpool W10112488 is a highly efficient and versatile appliance that has carved a niche for itself in the competitive world of kitchen gadgets. Designed primarily as a water filter, it boasts an impressive array of features and technologies, making it an essential addition to any home seeking cleaner and better-tasting drinking water.

One of the standout features of the W10112488 is its advanced filtration system. It utilizes a multi-stage filtration process to remove contaminants and impurities commonly found in tap water, such as chlorine, sediment, and rust. This ensures that the water you drink is not only safe but also tastes great. The filter has been certified to reduce harmful substances, giving owners peace of mind regarding their family's health and well-being.

The design of the W10112488 is another notable aspect. It is compact and lightweight, making it easy to install and replace on various refrigerator models. Its compatibility with multiple Whirlpool refrigerator models adds to its appeal, allowing users to enhance their existing appliances without hassle. Moreover, installation typically does not require any specialized tools, further simplifying the process for consumers.

In terms of longevity, the W10112488 filter has a significant lifespan. Depending on usage, it can last up to six months before needing replacement. This extended usage period not only ensures that users get optimal performance but also makes it a cost-effective solution for families concerned about ongoing expenses related to water filtration.

The filter's performance is also backed by innovative technologies. Whirlpool has engineered it to use a high-capacity design that maximizes the filter's effectiveness while maintaining a steady flow of water. This means users won't have to sacrifice convenience for quality. Whether it’s for brewing coffee, cooking, or direct consumption, the W10112488 delivers filtered water effortlessly.

Finally, eco-conscious consumers will appreciate Whirlpool's commitment to sustainability. By using this filter, households can reduce their reliance on bottled water, thus contributing to a significant reduction in plastic waste and benefiting the environment.

In summary, the Whirlpool W10112488 water filter combines advanced filtration technology, user-friendly design, longevity, and eco-friendliness, making it a smart choice for anyone looking to improve their home's water quality. With its features and efficiency, it stands as a testament to Whirlpool's dedication to consumer satisfaction and environmental responsibility.
Top Page Image Contents