Electrolux 88810 manual Setup, Washing cycle complete/Removing the washing, Memory 1, 2

Page 21

Washing cycle complete/Removing the washing

At the end of the cycle a long acoustic signal sounds 3 times (when the SOUND setting is NORMAL or LOW) and the messages “Cycle ended” and “Door openable” appear alternately in the display.

1.Open the door and remove the washing.

2.Turn the programme knob to OFF.

3.Turn off the tap.

4.After the wash, pull out the detergent dispenser drawer slightly to al- low it to dry. Leave the door slightly open to air the inside of the wash- ing machine.

If RINSE HOLD or NIGHT CYCLE was selected:

After a Rinse Hold or when a programme with NIGHT CYCLE has ended, the START/PAUSE indicator flashes. “Cycle ended” and “Door locked” appear alternately in the display.

The water must first be drained off:

–Turn the programme knob to OFF, then to DRAIN and press the START/PAUSE key (the water is drained without spinning),

or

–or turn the programme knob to OFF and then to SPIN. Change the spin speed if necessary and press the START/PAUSE key (the water is drained and the washing spun).

Setup

The special functions that can be set under Setup remain permanently stored independent of each washing cycle – even after the appliance has been switched off or the mains plug has been removed from the socket.

Memory 1, 2, 3

Programme combinations can be stored at programme knob positions MEMORY 1, 2, 3 and can then be selected using the programme knob. To do this the desired programme combination is first put together and then stored.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents
Lavamat Dear Customer Following symbols are used in the textContents Safety information concerning installation Installation and connection instructionsPrior to using the appliance for the first time SafetyChild safety Follow the Installation and connection instructionsResulting overheating may constitute a fire hazard General safetyCycle end at What is shown in the displayEasy Iron Programme overviewProgrammes/features Care Symbols1 N g u a g e Prior to using for the first timeR a c h e Programmende umPreparing and sorting washing Setting the timeCarrying out a wash programme prior to first use Preparing washingRunning a wash cycle Adding detergent /conditionerWashing powder/tablets for the main wash cycle If you are using liquid detergent Switching on the appliance/selecting a programChanging spin speed/selecting rinse hold LINEN/EASY CareCurrent load display Opening the door/Loading the washingSetup Setting options Prewashing To switch off the option Sensitive Prewash, Sensitive, Stain, Night CycleDelay Start Setting timesTime saving Time Saving Short or Very ShortStart in 4h Delay StartStart Press the OK key. Start in 0 min is shown in the displayStarting a programme WashingProgramme progress Interrupting a programme/Adding washingWashing cycle complete/Removing the washing SetupMemory 1, 2 If Rinse Hold or Night Cycle was selectedSetting the Memory Memory Store programChanging the Memory U n d N s e +Extra Rinse Set time LanguageClock Contrast and brightness Desired setting. WithEach press of the key or if Black triangle in the diaDeactivating the child safety device Child safety deviceCleaning procedure Cleaning and maintenanceDetergent dispenser drawer Washing drumWhat to do if Clean the glass in the door and the rubber collar regularlyDoor and rubber collar Remedying small malfunctionsTap turned off Turn the tap on There are grey stains on the washing If the wash result is not satisfactoryFoam can still be seen following the final rinse There are white residues on the washingCarrying out an emergency drain When the water has all drained awayDrain pump Disposal Packaging materialOld appliance Consumption values Technical dataThis washing machine cannot be built-in Safety information concerning installationWhen using a sack trolley to transport the washing machine Installing the applianceTransporting the appliance Removing the transit packagingWhere to install If the appliance is to stand on a base Making the appliance levelElectrical Connection Brown Live Wire coloured green and yellowConnecting the appliance to the water supply Permanent ConnectionPermitted water pressure 35m long pressure hose is supplied with the appliance Water inletFrom your Service Force Centre Water DrainageFor drainage into an outlet Pumping heights of over 1 metre Great Britain Warranty conditionsPage Page Customer Care 0870 5 929For general enquiries concerning Major AppliancesAEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG
Top Page Image Contents