Haier HWM85-728 user manual Safety precautions, Common phenomena

Page 4

Safety precautions

Trouble-shooting Answer to question

Please plug the power plug on special receptacle. Be sure to use three-pins

The washing machine must be positioned so that the plug is accessible. Be sure to pull the plug off and close the water faucet in

(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. Do not repair it by yourself.

power receptacle. Ensure that the earthing prong of the power receptacle is earthed

following cases: power failure, delivering the machine, setting the machine idle or

Phenomena

The reason

How to settle

reliably. Use leakage protector if possible.

cleaning the machine. Do not plug or pull the power plug with wet hand.

The digitron displays E0.

The drainage cannot work, or is too slow. The digitron displays E1.

The top lid is opened during reserve procedure.

Is the drain hose put down?

Is the drain hose blocked?

Close the top lid.

Put down the drain hose. Open and close the top lid once.

Clean the foreign material. Open and close the top lid once.

Do not bend ,extend, twist, bind by force. Do not press or nip it with weight. Keep the pin of the power plug clean, if the power plug is polluted with dust, please wipe with dry cloth carefully.

If the power cord or the power plug is bad, to avoid risk it is required to have it replaced by the technicians of our special shop or the after-sale service department.

In case the washing machine is installed on ground

Do not use water hotter than 50 .

with carpet, do not block the ventilation hole with

 

carpet.

 

The ventilation holes

 

at the bottom

 

Carpet

 

Do not put the machine at damp place like

Do not wash water-proof laundries like

the bathroom. Never wash it with water. Do

the raincoat, bike covers etc. to avoid

not put wet laundries on the control panel.

abnormal vibrations in spinning.

It stops running in midway. The digitron displays E2.

The safety switch acts, and the spinning cannot work. The digitron displays E3.

The water filling does not work, or is slow. After about 30 minutes later, the digital displays E4.

The digitron displays E6.

Not wash

The machine does not act

Not spin

There's abnormal sound inside the machine

The water tap leaks

The top lid is not closed.

Are the laundries put slantingly? Is the machine slanting?

Is the water tap opened, or is there water supply failure?

Is the water inlet valve blocked? Is the water pressure too low?

The water level sensor is bad.

Is there power failure?

Is the power plug inserted tightly?

Is the water level reached preset position?

Is the power plug inserted tightly? Is the top lid closed reliably?

Are the laundries set flat?

Is the machine slanting?

Are the laundries put slantingly in spinning? Are there any foreign materials?

Is the screw of the jointer of water inlet hose loose or awry?

Close the top lid.

Reorder the laundries. Close the top lid.

Th machine will start running after 10 seconds of being placed horizontally.

Open the water tap. Push the start/Pause button once.

Clean the water inlet valve then push

the start/Pause button once.

Push the Start/Pause button once.

Please contact the after-sales service department.

Please use it when there's power supply. Insert the power plug tightly.

Fill water to the preset position.

Insert the power plug tightly.

Close the top lid.

Set the laundries flat.

Adjust the machine to be even

Reorder the laundries and close the top lid. Remove the foreign materials.

Fasten the screw of the jointer properly.

Do not let the machine share one receptacle with other electric appliances. If the plugging into the receptacle is loose, do not use the plug any more.

2

Common phenomena

Phenomena

The spinning is intermittent when it starts.

The wash procedure is paused.

Push the PROGRAM button to select SPIN, but it doesn't work.

The pulsator pauses during water inlet in wash and rinse.

There may be some water flowing out of the drain hose in the first use of the machine.

Explanation

Balance the laundries to avoid slanting.

The cloth sensor is checking the cloth, it will add water after 48 seconds.

The program is setting the drain time. Some time is needed before it starts spinning.

It is to avoid splashing during water inlet.

It is the water remained in the factory inspection of performance.

Image 4
Contents Fully Automatic Washing Machine Contents Meaning and description of the symbols Names of the partsSafety precautions Common phenomenaDisposal after washing Safety precautions Install the bottom plate Installation and adjustmentPush the Process button How to change the direction of the drain hose START/PAUSE buttonInstall the water inlet hose Confirm the water faucetPROCESSbutton SELF-PROGRAMbutton and + -buttonPower ON/OFF button Use the operation buttonsConnection between the water inlet hose and the washer Dismantle the water inlet hosePreparation before washing How to use the softenerPut in the laundries