LG Electronics D5988B, D3788W, D5988W manual Part 4 Electrical Requirements for Electric Dryers

Page 15

Part 4 ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYERS

4.Put the hooked shape ends of the wire under the screw of the terminal block(hooked end facing rightward) and squeeze the hook together and screw tightly.

5.Put the hooked shaped ends of the other power supply cable wires under the outer terminal block screws(hooked end facing right) and squeeze the hooked ends together and screw tightly.

6.Tighten strain relief screws.

7.Place the tab of terminal block cover into slot of dryer rear panel. Make sure cover with screw.

3-wire connection : Direct wire

Important : The places wherea 4-wire connection is needed are mobile homes and areas that local codes do not admit the use of 3-wire connections.

At least, 5ft(1.52m) of extra length is required for dryer to be able to move.

Peel 5 in (12.7cm) of external covering from end

of cable, leaving bare ground wire at 5 in (12.7cm). Cut 11/2 in. (3.8cm) from 3 remaining wires. Strip insulation back 1in. (2.5cm). Shape ends of wires into a hook shape.

"

1

cm)

 

.5

(2

 

2"

 

3V

 

.9 cm)

(8

 

Then, put the hooked shape end of the wire under the screw of the terminal block(hooked end facing rightward) and pinch the hook together and screw tightly.

1.Take off center terminal block screw

2.Put the hooked end of the neutral wire(white) of power supply cable under the center screw of terminal block). Squeeze the hooked end together

3.Connect the hooked ends of the other power supply cable to the center screw of terminal block.

4.Screw strain relief tightly.

5.Place tab of terminal block cover into slot of dryer rear panel. Make sure cover with screw.

 

c

 

b

 

d

a

e

 

a.External ground connector

b.Neutral grounding wire (white)

c.Center silver-colored terminal block screw

d.Neutral wire (white or center wire)

e.3/4 in. (1.9 cm) UL-listed strain relief

1 5

Image 15
Contents Electric and Gas Dryer Table of Contents Part 1 Specifications Seeking Warranty Assistance Part 2 Important Warranty and Safety InstructionsImportant Safety Instructions California safe drinking water and toxic enforcement act What to do if YOU Smell GASPositioning the Dryer Part 3 Initial Steps for Installing Your DryerProcedure for Reversing the Door Clean old ducts before installing this dryer Connecting the Exhaust and Venting SystemElectrical Plug Connections for Electric Dryer Only Connection of Gas SupplyConfirming Heat Source in Gas Dryers Preparation of the DryerConfirming Heat Source Operation Dryer AirflowPart 3 Initial Steps for Installing Your Dryer Instructions for Grounding of your Electric Electric Dryer Part 4 Electrical Requirements for Electric DryersWire receptacle Nema type14-30R Wire directWire connection Direct wire Wire receptacle Nema type10-30RPart 4 Electrical Requirements for Electric Dryers Wire connection Option 1 3-Wire Connection with a Power Supply CordOption 2 4-wire connection with a Power supply cord Option 3 Optional 3-wire connection Part 5 Electrical Requirements for GAS Dryers Volt, 60 Hertz, with 3-Prong Grounding PlugElectrical Requirements for Your Dryer Part 6 GAS Requirements and Instructions Exhaust Requirements and Instructions Part 7 Exhaust Requirements and MaintenanceCleaning the Lint Screen Exhaust and Dryer MaintenanceFire Hazard Using Your DryerPart 8 Operating Your Dryer Explosion HazardTo use a Manual Dry Cycle Pausing or RestartingTo use a Sensor Dry Cycle Stopping Your DryerSensor Dry Cycle Cycle DescriptionsChild Lock Sensor Dry Temp Time Cycles Load TypeModifiers OptionsRack Dry Anti BacterialTo use the Rack DRY To recall your stored Custom Program Clean the door and its openingCustom Programming Beeper To store a CustomQuestion What to Do Part 9 Troubleshooting GuideProblemThere is Lint on my Clothes ProblemIt takes too long for my clothes to dry LG Dryer Limited Warranty USA