Frigidaire 137153400A Electrical connection non-Canada 4-wire cord, General installation, 14-30R

Page 11

Electrical connection (non-Canada) 4-wire cord

- ELECTRICAL SHOCK HAZARD - Failure to disconnect power source before servicing could result in personal injury or even death.

1.Turn off power supply to outlet.

2.Remove the screw securing the terminal block access cover in the upper corner on the back of the dryer.

3.Install a UL-approved strain relief according to the power cord/ strain relief manufacturer’s instructions in the power cord entry hole below the access panel. At this time, the strain relief should be loosely in place.

4.Thread an UNPLUGGED, UL-approved, 30 amp. power cord, NEMA 14-30 type ST or SRDT, through the strain relief.

5.Disconnect the internal (WHITE) dryer harness ground wire from the (GREEN) ground screw next to the terminal block.

6.Attach the ground (GREEN) power cord wire to the cabinet with the ground (GREEN) screw. Tighten the screw securely.

7.Move the internal dryer harness ground (WHITE) wire to the terminal block and attach it along with the neutral (WHITE) power cord wire conductor to the center, SILVER colored terminal on the terminal block. Tighten the screw securely.

8.Attach the RED and BLACK power cord conductors to the outer, BRASS colored terminals on the terminal block. Tighten both screws securely.

- ELECTRICAL SHOCK HAZARD - Do not make a sharp bend or crimp wiring/conductor at connections.

9.Follow manufacturer’s guidelines for firmly securing the strain relief and power cord.

10.Reinstall the terminal block cover.

 

 

 

Neutral

4-wire

30 AMP

Ground

(WHITE wire)

 

 

 

 

receptacle

NEMA 14-30

(GREEN wire)

 

 

 

 

 

 

(NEMA type

 

 

 

14-30R)

 

 

 

GREEN

Neutral

ground screw

terminal

 

WHITE

GREEN

neutral wire

 

ground wire

 

Move internal

 

ground (WHITE)

 

wire to neutral

BLACK

(silver) terminal

or RED

for 4-wire system

power wire

 

BLACK

 

or RED

 

power wire

General installation

1. Connect the exhaust duct to the outside exhaust system (see pages 4 through 6). Use of a 4” (10.2 cm) clamp (item A) is recommended to connect the dryer to the exhaust vent system. Use metal foil tape to seal all other joints.

2. Carefully slide the dryer to its final position. Adjust one or more of the legs until the dryer is resting solidly on all four legs. Place a level on top of the dryer. The dryer MUST be level and resting solidly on all four legs. Rock alternating corners to check for stability. Remove and discard door tape.

A

Be sure the power is off at a circuit breaker/ fuse box before plugging the power cord into an outlet.

3. Plug the power cord into a grounded outlet.

4. Turn on the power at the circuit breaker/fuse box.

5. Read the Use & Care Guide provided with the dryer. It contains valuable and helpful information that will save you time and money.

6.If you have any questions during initial operation, please review the “Avoid Service Checklist” in your Use & Care Guide before calling for service.

7. Place these instructions in a location near the dryer for future reference.

A wiring diagram and technical data sheet are located inside the dryer console.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Installation Instructions Pre-Installation Requirements Table of ContentsImportant Safety Instructions Electrical requirements for gas dryer Electrical System RequirementsElectrical requirements for electric dryer Exhaust system requirements Gas supply requirementsExhaust system requirements Exhaust direction Manufactured or mobile home installationCloset door Do not Install Your DryerClearance requirements Electrical Shock Hazard Front Console DimensionsRear Console Dimensions Electrical installationGrounding requirements Gas dryer USA and Canada Grounding requirements Electric dryer USAGrounding requirements Electric dryer Canada 10-30R WireGas connection 14-30R Electrical connection non-Canada 4-wire cordGeneral installation Door Reversal Replacement partsAccessories Requisitos de preinstalación ÍndiceInstrucciones importantes de seguridad Requisitos eléctricos de la secadora a gas Requisitos del sistema eléctricoRequisitos eléctricos de la secadora eléctrica Requisitos del sistema de escape Requerimientos del suministro de gasPeligro DE Incendio Requisitos del sistema de escape continuaciónInstalación en una casa rodante Requisitos del sistema de ventilación continuaciónPuerta del armario Requisitos de despejeNo Instale LA Secadora Instalación eléctrica Dimensiones Consola FrontalRequisitos de conexión a tierra secadora eléctrica Canadá Trifilar Conexión de gasConexión eléctrica fuera de Canadá trifilar Desconecte el suministro eléctrico del tomacorrienteInstalación general Accesorios Puerta ReversiblePiezas de repuesto

137153400A specifications

The Frigidaire 137153400A is a highly functional part designed for a range of Frigidaire washing machines, catering to diverse household laundry needs. This part is an essential component that contributes to the seamless operation of washing appliances, ensuring user satisfaction through durability and efficient performance.

One of the main features of the Frigidaire 137153400A is its robust design that includes high-quality materials. This durability ensures that it withstands regular usage, thus minimizing the need for frequent replacements. The precise engineering of the part guarantees that it fits perfectly into compatible washing machine models, which streamlines the installation process and helps maintain optimal washing results.

In terms of technology, this component excels in enhancing the overall efficiency of washing machines. Its role is crucial in regulating water flow and performing necessary operations that enhance water drainage and cycle completion. This functionality not only improves washing performance but also reduces water waste, aligning with modern environmental standards.

Another characteristic of the Frigidaire 137153400A is its compatibility with a variety of Frigidaire washing machine models. This versatility makes it a valuable addition for homeowners who may want to upgrade or replace parts in their existing appliances without downgrading performance. Homeowners can benefit from the cost savings associated with keeping their current washing machines in optimal working condition rather than investing in new units.

In summary, the Frigidaire 137153400A is a well-engineered component that offers a blend of durability, efficiency, and compatibility with Frigidaire washing machines. Its design not only supports improved washing performance but also minimizes environmental impact through better water management. For those seeking to maintain their appliances effectively, this part stands as an indispensable choice that underscores Frigidaire's commitment to quality and technological advancement in household appliances. Investing in components like the Frigidaire 137153400A ensures that laundry tasks can be completed with ease and reliability, meeting the demands of a modern household.
Top Page Image Contents