GE PCVH480EK Tools and Materials YOU will Need to Install Exhaust Duct, Exhaust System Checklist

Page 17

Installation Instructions

EXHAUSTING THE DRYER

WARNING – To reduce the risk of fire or personal injury:

This clothes dryer must be exhausted to the outdoors.

Use only 4rigid metal ducting for the home exhaust duct.

Use only 4rigid metal or UL-listed flexible metal (semi-rigid or foil-type) duct to connect the dryer to the home exhaust duct. It must be installed in accordance with the instructions found in “Connecting the Dryer to House Vent” on page 18 of this manual.

Do not terminate exhaust in a chimney, a wall, a ceiling, gas vent, crawl space, attic, under an enclosed floor, or in any other concealed space of a building.

Never terminate the exhaust into a common duct with a kitchen exhaust system. A combination of grease and lint create a potential fire hazard.

Do not use duct longer than specified in the exhaust length table. Longer ducts can accumulate lint, creating a potential fire hazard.

Never install a screen in or over the exhaust duct. This will cause lint to accumulate, creating a potential fire hazard.

Do not assemble ductwork with any fasteners that extend into the duct. These fasteners can accumulate lint, creating a potential fire hazard.

Do not obstruct incoming or exhausted air.

Provide an access for inspection and cleaning of the exhaust system, especially at turns and joints. Exhaust system shall be inspected and cleaned at least once a year.

This dryer comes ready for rear exhausting. If space is limited, use the instructions on pages 21–23 to exhaust directly from the sides or bottom of the cabinet.

TOOLS AND MATERIALS YOU WILL

NEED TO INSTALL EXHAUST DUCT

Phillips-head screwdriver

Vent hood

Duct tape or duct clamp

Drill with 1/8drill bit (for bottom venting)

Rigid or UL-listed flexible

metal 4(10.2 cm) duct

Hacksaw

17

EXHAUST SYSTEM CHECKLIST

HOOD OR WALL CAP

Terminate in a manner to prevent back drafts or entry of birds or other wildlife.

Termination should present minimal resistance to the exhaust airflow and should require little or no maintenance to prevent clogging.

Never install a screen in or over the exhaust duct .

Wall caps must be installed at least 12above ground level or any other obstruction with the opening pointed down.

SEPARATION OF TURNS

For best performance, separate all turns by

at least 4 ft . of straight duct, including distance between last turn and dampened wall cap.

For turns less than 4 ft . apart, see the Ducting Component Equivalency Chart .

SEALING OF JOINTS

All joints should be tight to avoid leaks. The male end of each section of duct must point away from the dryer.

Do not assemble the ductwork with fasteners that extend into the duct . They will serve as a collection point for lint .

Duct joints should be made air- and moisture-tight by wrapping the overlapped joints with duct tape or aluminum tape.

Horizontal runs should slope down towards outdoors 1/4per foot .

INSULATION

Ductwork that runs through an unheated area or is near air conditioning should be insulated to reduce condensation and lint buildup.

Image 17
Contents Dryers Proper Installation Your Laundry Area When not Using Your Dryer Quick Start PowerSensor Dry Level Dry CyclesTimed Dry Dry Temp Clean Lint Filter messageDamp Alert Delay StartExtend Tumble Lock SignalSorting and Loading Hints Care and Cleaning of the DryerFabric Care Labels Dry LabelsBefore YOU Begin For Your SafetyElectrical Connection Dryer DimensionsUnpacking Your Dryer Mobile or Manufactured Home Installation Bathroom or Bedroom InstallationUndercounter Installation Materials YOU will Need Tools YOU will NeedGrounding Instructions Electrical Requirements For Electric DryersConnecting Dryer Using 3-WIRE Connection Installation Instructions Connecting AN Electric DryerExhaust System Checklist Tools and Materials YOU will Need to Install Exhaust DuctDo not Connecting the Dryer to House VentUSE only Metal Duct 4″ Diameter 102 mm Standard Rear Exhaust Recommended Configuration to Minimize Exhaust BlockageAdding a NEW Duct Side VentingBottom Venting Side VentingBottom Venting Plug Dryer Level the DryerDryer Startup ServicingHardware Used Important NotesBefore YOU Start Remove the Door AssemblyReplace Door Assembly Minimum clearance to combustible surfaces Installation Preparation Installing the Stack Bracket KITFinalize the Installation Install Bracket to WasherInstall Dryer and Bracket on Dryer GEAppliances.com Before you call for service… Timed DRY Clothes shrink Warrantor General Electric Company. Louisville, KY What Is Not Covered in the United StatesWe Will Replace What Is Not Covered in Canada GE Dryer Warranty. For customers in CanadaConsumer Support
Related manuals
Manual 108 pages 47.24 Kb

PCVH480EK, PCVH485EK specifications

The GE PCVH485EK and PCVH480EK are innovative electric ranges that embody the fusion of modern technology and user-friendly design, making them standout appliances for contemporary kitchens. These models showcase exceptional cooking performance and versatility, catering to diverse culinary needs and preferences.

One of the key features of both the PCVH485EK and PCVH480EK is the inclusion of the innovative Convection Cooking technology. This advancement ensures even heat distribution throughout the oven, allowing dishes to cook uniformly and thoroughly. Whether baking pastries or roasting meats, users can expect professional-quality results. The range features multiple cooking modes, including Bake, Broil, and Roast, providing flexibility for various cooking techniques.

The ranges also boast a self-cleaning oven, which simplifies maintenance and keeps the appliance looking new. The self-cleaning feature utilizes high temperatures to burn away food residues, minimizing the need for harsh chemicals and labor-intensive scrubbing. Additionally, both models have a spacious oven capacity, accommodating large meals and multiple dishes simultaneously, making them ideal for family gatherings and entertaining.

Another standout aspect of these models is their user-friendly controls. The digital display and intuitive interface make it easy to navigate through cooking settings and adjust temperatures. For those who appreciate precise cooking, the ranges come with built-in temperature probes that allow users to monitor the internal temperature of their dishes accurately.

Safety is also a priority in the design of the PCVH485EK and PCVH480EK. Both models are equipped with features like a kitchen timer, oven lock, and a reversible cast-iron griddle, ensuring a safe and efficient cooking experience. The radiant cooktop delivers rapid heating for quick meal preparation and features multiple burners with varying heat outputs to accommodate different cooking techniques.

In addition to their impressive performance and safety features, these ranges are designed with a modern aesthetic in mind. Their sleek stainless-steel finish and clean lines make them a stylish addition to any kitchen decor.

Overall, the GE PCVH485EK and PCVH480EK electric ranges are high-performing, dependable appliances that combine advanced cooking technologies with user-friendly features and elegant design, making them a perfect choice for any home chef looking to enhance their culinary experience.