Kenmore 110.6706, 110.6707 Type of Load Time, When using Air Dry, Drum Light, Damp Dry Signal

Air Dry

Use the Air Dry Modifier for items that require drying without heat such as rubber, plastic and heat-sensitive fabrics. This table shows examples of items that can be dried using Air Dry.

Type of Load		Time*
		(Minutes)
Foam rubber - pillows,	padded bras, stuffed toys	20	- 30
Plastic - Shower curtains, tablecloths		20	- 30
Rubber-backed rugs		40	- 50
Olefin, polypropylene,	sheer nylon	10	- 20

*Reset cycle to complete drying, if needed.

When using Air Dry

•Check that coverings are securely stitched.

•Shake and fluff pillows by hand periodically during the cycle.

•Dry item completely. Foam rubber pillows are slow to dry. NOTE: Air Dry is not available with Auto Dry Cycles.

You can customize your cycles by selecting options.

OPTIONS

Drum Lght

W,h, kle _u_r_ go

Drum Light

On some models, you may select Drum Light to turn on the light inside the dryer drum. During a cycle, if Drum Light is selected, the drum light turns on and will remain on until DRUM LIGHT is pressed again, the door is open and closed, or the door is left open for 5 minutes.

When the dryer is not running, the drum light will turn on when DRUM LIGHT is pressed or the dryer door is opened, and it will remain on until the dryer door has been open for 5 minutes, the dryer door is closed or DRUM LIGHT is pressed again.

Press DRUM LIGHT at any time to turn the drum light ON or OFR

Damp Dry Signal

Select the Damp Dry Signal to alert you that your clothes are approximately 80% dry or suitable for ironing. This is useful when you want to remove lightweight items in a mixed load to avoid overdrying or remove partially dry items that may need ironing.

The DAMP DRY SIGNAL is useful when drying bedsheets/linens in a mixed load. When the signal goes off, open the door to stop the dryer, rearrange the load inside the dryer, close the door and restart the dryer to finish the drying cycle. Rearranging the load will aid in the drying process.

NOTE: The Damp Dry Signal is available only with the Auto Dry Cycles.

WRINKLE GUARD _ (30, 60, 90, 150 minutes)

WRINKLE GUARD _ helps smooth out wrinkles that may form when clothes are not removed promptly at the end of a cycle. During this option, the dryer stops tumbling and then tumbles again for a brief period without heat when pressed.

•Press WRINKLE GUARD _ to get heat-free, periodic tumbling at the end of a cycle. WRINKLE GUARD _ periodically starts and stops the dryer, tumbling the load without heat for 30, 60, 90 or 150 minutes (depending on your model) unless you open the dryer door.

•Stop WRINKLE GUARD ® at any time by pressing WRINKLE GUARD _, opening the dryer door or pressing STOR

•For the Casual Cycle, WRINKLE GUARD ® is preset to ON. The other Auto Dry Cycles will retain the WRINKLE GUARD ® setting. For example, if you select WRINKLE GUARD ® in the Normal cycle, WRINKLE GUARD ® will be on the next time you select the Normal cycle.

NOTE: If you do not select WRINKLE GUARD ®, the dryer stops after cool down.

Cycle Signal

The Cycle Signal produces an audible sound when the drying cycle is finished. Promptly removing clothes at the end of the cycle reduces wrinkling.

Press CYCLE SIGNAL VOLUME until the desired volume (Loud or Soft) is selected. On some models, press CYCLE SIGNAL to turn the Cycle Signal On or Off.

OnLoud

OffSoft

Cycle Signal Cycle Signal Volume

NOTE: When WRINKLE GUARD _ is selected, a tone sounds

every 5 minutes until the clothes are removed, or WRINKLE GUARD _ ends.

You can change Auto and Timed Cycles, Modifiers and Options anytime before pressing Start.

•Three short tones sound if an unavailable combination is selected. The last selection will not be accepted.

Changing Cycles after pressing Start

1.Press STOP twice.

2.Select the desired cycle and options.

3.Press START. The dryer starts at the beginning of the new cycle.

NOTE: If you do not press Start within 5 minutes of selecting the cycle, the dryer automatically shuts off.

Changing Modifiers and Options after pressing Start

You can change a Modifier or Option anytime before the selected Modifier or Option begins.

1.Press STOP once.

2.Select the new Modifier and/or Options.

3.Press START to continue the cycle.

NOTE: If you happen to press STOP twice, the program clears and your dryer shuts down. Restart the selection process.

22