JVC KD-SV3104 When using the optional stay, When installing the unit without using the sleeve

Page 36

When using the optional stay

Fire wall

Dashboard

Stay (option)

When installing the unit without using the sleeve

In a Toyota for example, first remove the car radio and install the unit in its place.

*2 Not included for this unit.

Flat type screws (M5 x 8 mm)*2

Bracket*2

Screw (option)

Install the unit at an angle of less than 30˚.

Flat type screws (M5 x 8 mm)*2

Pocket

Bracket*2

Note : When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws are used, they could damage the unit.

Removing the unit

Before removing the unit, release the rear section.

Insert the two handles, then pull them as illustrated so that the unit can be removed.

ELECTRICAL CONNECTIONS

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit.

Be sure to ground this unit to the car’s chassis again after installation.

Notes:

Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer.

It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 to 8 ). If the maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 24 of the INSTRUCTIONS).

To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.

The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

Heat sink

PRECAUTIONS on power supply and speaker connections:

DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged.

BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.

TROUBLESHOOTING

The fuse blows.

*Are the red and black leads connected correctly?

Power cannot be turned on.

*Is the yellow lead connected?

No sound from the speakers.

*Is the speaker output lead short-circuited?

Sound is distorted.

*Is the speaker output lead grounded?

*Are the “–” terminals of L and R speakers grounded in common?

Noise interfere with sounds.

*Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?

Unit becomes hot.

*Is the speaker output lead grounded?

*Are the “–” terminals of L and R speakers grounded in common?

This unit does not work at all.

*Have you reset your unit?

2

Image 36
Contents KD-SV3104 How to reset your unit How to forcibly eject a discContents How to read this manual How to use the Mode buttonControl panel KD-SV3104 Parts identificationDisplay window Remote controller RM-RK120 Installing the lithium coin battery CR2025Main elements and features To drop the volume in a moment ATT Getting startedCanceling the display Demonstrations Setting the clockTo activate the display demonstration Radio operations To tune in to a station manuallyWhen an FM stereo broadcast is hard to receive Storing stations in memoryListening to a preset station Manual presettingDisc operations About MP3 and WMA discsMP3 and WMA discs playback/search order Prohibiting disc ejection To stop play temporarilyTo stop play and eject the disc Playing a disc in the CD changer About the CD changerMP3 discs playback/search order in the CD changer To fast-forward or reverse the trackTo go to the next or previous tracks To correct a mis-entry and to return to the previous menu For MP3 discs For WMA discsMP3/WMA control screen Operations While playing a discText / , or a While playing an MP3 Or WMA discTo select a folder To select a trackMode Plays repeatedly Selecting the playback modesMode Sound adjustments For Preset valuesAdjusting the sound To do RangeGeneral settings PSM Basic procedureIndications Selectable settings, reference Detaching the control panel Detaching the control panelExternal component operations Playing an external componentMaintenance More about this unit General settings-PSM Playing an MP3/WMA discChanging the source Ejecting a discTroubleshooting Symptoms Causes RemediesDisc playback MP3/WMA playback MP3/WMA playback CD changer Specifications Audio Amplifier SectionRefer to page of How to reset your unit Having Trouble with operation?Installation/Connection Manual Parts list for installation and connectionWhen using the optional stay When installing the unit without using the sleevePrecautions on power supply and speaker connections Removing the unitConnecting the parking brake wire Connecting the crimp connectorTypical Connections Connecting the monitor Connecting the external amplifierConnecting the external components KV-MR9010