American Dryer Corp ML-175DR installation manual Not be Reduced Anywhere Downstream of the Dryer

Page 16

NOTE: As per the National Fuel Gas Code, “Exhaust ducts for Type 2 clothes dryers shall be constructed of sheet metal or other noncombustible material. Such ducts shall be equivalent in strength and corrosion resistance to ducts made of galvanized sheet steel not less than 26 gauge (0.0195-inches [0.5 mm]) thick.”

IMPORTANT: It is recommended that exhaust or booster fans not be used in the exhaust ductwork system.

Outside Ductwork Protection

To protect the outside end of horizontal ductwork from the weather, a 90° elbow bent downward should be installed where the exhaust exits the building. If the ductwork travels vertically up through the roof, it should be protected from the weather by using a 180° turn to point the opening downward. In either case, allow at least twice the diameter of the duct between the duct opening and the nearest obstruction.

IMPORTANT: DO NOT use screens, louvers, or caps on the outside opening of the exhaust ductwork.

2.Single Dryer Venting

Where possible, it is suggested to provide a separate exhaust duct for each dryer. The exhaust duct should be laid out in such a way that the ductwork travels as directly as possible to the outdoors with as few turns as possible. It is suggested that the use of 90° turns in the ducting be avoided; use 30° and/or 45° angles instead. The shape of the exhaust ductwork is not critical as long as the minimum cross section area is provided.

IMPORTANT: The minimum duct size for a gas unit is 12-inches (30.48 cm) for a round duct and 10-inches x 10-inches (25.4 cm x 25.4 cm) for a square duct. The minimum duct size for a steam unit is 20-inches (50.80 cm) for a round duct and 18-inches x

18-inches (45.72 cm x 45.72 cm) for a square duct. THE DUCT SIZE MUST

NOT BE REDUCED ANYWHERE DOWNSTREAM OF THE DRYER.

12

American Dryer Corp.

113406-1

Page 15 Page 17
Image 16
Page 15 Page 17
Contents ML-175DR Installation Manual Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Safety Precautions SectionStandards Specifications SpecificationsSpecifications GAS and Steam Installation Procedures Location RequirementsUNPACKING/SETTING UP American Dryer Corp 113406-1 Dryer Enclosure Requirements Fresh AIR Supply Requirements Exhaust Requirements General Exhaust Ductwork InformationNot be Reduced Anywhere Downstream of the Dryer 113406-1 Outside Ductwork Protection 113406-1 American Dryer Corp 113406-1 Electrical Information Electrical RequirementsElectrical Service Specifications PER Dryer 113406-1 GAS Information Type of GAS American Dryer Corp 113406-1 113406-1 Steam Information Operating Steam PressureSteam Damper System Compressed Air Supply Air Pressure 113406-1 Preparation for OPERATION/START-UP Preoperational Tests Basket Tumbler Coating Compressed Air Supply Air Pressure Compressed AIR RequirementsShutdown Instructions Service SERVICE/PARTS InformationParts Warranty Information Returning Warranty CardsWarranty Returning Warranty Parts113406-1 Routine Maintenance CleaningSteam Dryers Adjustments LubricationManual Reset Burner HI-LIMIT Instructions PhaseSectionviii Data Label InformationProcedure for Functional Check Replacement Components American Dryer Corp 113406-1 Fire Suppression System In Action Fire Suppression SystemInstallation Before YOU Start Check Local Codes and PermitsTypical Water Supply Inoperative Fire Suppression System Theory of Operation Fire Suppression System Water Valve Check Starting a Cycle When Computer is in F.S.S. is Disabled Mode ADC113406 1 01/07/05

ML-175DR specifications

American Dryer Corp ML-175DR is a high-efficiency, state-of-the-art hand dryer designed to provide a superior drying experience in public restrooms and commercial environments. With its sleek and modern design, the ML-175DR not only enhances the aesthetic appeal of any facility but also offers numerous practical benefits.

One of the standout features of the ML-175DR is its powerful motor, which generates a strong airflow of up to 17,000 RPM. This ensures that hands are dried quickly and effectively, taking only about 10 to 15 seconds to achieve optimal dryness. This efficiency significantly reduces waiting time for users, making it a convenient choice for high-traffic areas.

The ML-175DR incorporates advanced sensor technology that allows for touchless operation. The built-in infrared sensors detect the presence of hands beneath the nozzle, automatically activating the drying process. This feature not only promotes hygiene by minimizing contact with surfaces but also helps conserve energy, as the dryer only operates when needed.

Another noteworthy characteristic of the ML-175DR is its eco-friendly design. It is constructed with energy-efficient components that use significantly less power compared to traditional hand dryers. This not only reduces electricity costs but also supports sustainability efforts by minimizing the carbon footprint associated with restroom facilities.

Moreover, the ML-175DR includes an adjustable airspeed feature, allowing users to customize their drying experience according to different environments. Whether it’s a busy restaurant or a quiet office, the adjustable settings enable optimal performance tailored to the specific needs of each location.

In terms of durability, the ML-175DR is built with heavy-duty materials that ensure longevity, making it a reliable choice for various commercial and public settings. Its robust construction is resistant to wear and tear, which is essential for hand dryers that see frequent use.

In summary, the American Dryer Corp ML-175DR stands out for its powerful yet efficient drying capabilities, touchless operation, eco-friendly design, adjustable airspeed, and durable construction. These features make it an excellent choice for modern facilities looking to enhance hygiene, improve user experience, and promote sustainability.
Top Page Image Contents