Maytag MCE8000AY manual Relay Header Connections Connector Description, Name

Page 18

Troubleshooting Procedures

!WARNING

To avoid risk of electrical shock, personal injury or death, disconnect power to unit before servicing, unless testing requires power.

Relay Header Connections
Relay	Connector	Description	Voltage
Name	Name
K9	NO	L1 to relay	120 VAC
	COM	L1 to lower dryer motor	120 VAC
K8	NO	L1 to relay	240 VAC
	COM	L1 to lower dryer heater center tap	240 VAC
K7	NO	L1 to relay	240 VAC
	COM	L1 to lower dryer	240 VAC

Power and Relay Board Connectors

Connector

Name

Pin

Number

Description

Voltage

J5	1	L1 to shaker motor		120	VAC
	2	L1 to upper cabinet lamp	120		VAC

	3	Neutral to shaker & lamp assembly	120		VACN

	4	Unassigned
J6B	1-12	See J6A in Logic Board	5 & 12
		Connectors Table		VDC
J7	1	Neutral to Power & Relay Board	120		VACN

	2	L2 to Power & Relay Board	120		VAC

	3	Gas Igniter Sense	120		VAC
	4	Lower Door Switch	120		VAC

	5	L1 to Power & Relay Board	120		VAC

J9	1	Relay to upper blower motor	120		VAC

	2	Unassigned
	3	Unassigned

	4	Unassigned

	5	Relay connects upper heater to L2	120		VAC

	6	Relay to upper dryer damper	120		VAC

	7	Spare relay output	120		VAC

	8	Relay to water valve	120		VAC

	9	Unassigned

	10	Relay connects upper heater to L2	120		VAC

J11B	1-5	See J11A in Logic Board	120		VAC
		Connectors table (Pin #3 is not
		used).

Note: VACN is the neutral wire of a 120V supply.

18

16022785 Rev. 0

©2003 Maytag Appliances Company

Image 18

Contents Neptune DC Customer Service Support Center Recognize Safety Symbols, Words, and LabelsWeb Site Telephone Number Table of Contents Important Safety Information Gas Connection Information Electrical Service InformationAbout Ground Wires Electrical DryersImportant Safety Information Testing for Gas Leaks Gas ConnectionAltitude Orifice Part Ft M Size # Number Extended Service Plan ServiceParts and Accessories PropaneE 8 0 0 Drying Center NomenclatureDrying Center Specifications Will not start or run Maytag Neptune Drying CenterWill Not Run Will Not Dry Gas ModelsNoisy and/Or Vibration Troubleshooting the Sensor-Dry circuitSystem Check Mode Rd**Read Sensor InputsSensor Display Menu Diagnostic CodesDL****Accessing Diagnostic Codes Sc***Upper and Lower Dryer Sub-system Check UtilitiesDiagnostic Codes RS Reset to Factory Default Conditions Code Description Trigger Action TakenCodes Visible To The Consumer Enter The Diagnostic Utilities MenuCancel the Read Sensor Display Function CS******View Cycle StatisticsMembrane Pad Continuity Checks Location Description Plug Number Pin NumberJ1A Relay Header Connections Connector Description NameLower Door Reversal/Removal Shaker RemovalDoor Hook Removal Console Removal Front Access Panel Removal Logic Board RemovalDisassembly Procedures Tumbler Drum Removal Heater Assembly Removal Relay Board Removal Blower and Motor RemovalWater Valve Removal Steamer Blower RemovalSteamer Heater Removal Appendix a Maytag Appliances Company 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev Appendix B Maytag Appliances Company 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev 16022785 Rev